RECORDING
Manual recording from external CD player
|
|
|
|
|
|
| EASY JOG |
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| STORE/MENU CANCEL/DELETE | PLAY/PAUSE | STOP | OPEN/CLOSE | ||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| CD |
|
|
|
| ENTER |
|
|
|
|
| |
OPEN/CLOSE | PLAY/PAUSE | STOP | RECORDING | FINALIZE |
|
|
|
|
|
|
|
|
|
|
|
| TYPE |
| ERASE | EXT | SOURCE |
|
|
|
|
|
| ||
|
|
| RECORD |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
| CDR |
|
|
|
|
|
|
|
|
|
| PROG | SHUFFLE | DISPLAY | SCROLL | REPEAT | DJ MODE |
|
| ||
Important:
-Recording from
-Only make analogue recordings when digital recording is not possible.
Preparing for manual recording
1 Make sure the disc is absolutely free of scratches and dust particles.
2 Press EXT(ernal) SOURCE repeatedly until (depending on the connection used):
➜DIGITAL I, OPTICAL I or ANALOG lights up and DIGITAL 1, OPTICAL or ANALOG appears on the display.
REM REC | TIME TRACK | TOTAL REM | TRACK TIME | STEP |
SYNC MANUAL |
| RECORD |
| PROG |
DIGITAL I | CD | CHANGER | CD | SHUFFLE ALL |
OPTICAL I | RW |
| RW | REPEAT |
ANALOG |
| SCAN TRACK | ||
|
|
|
•When Auto Track is On (default setting), track numbers will automatically be increased during recording.
•To switch off the Auto Track function you have to enter Menu mode.
If you wish to increase track numbers manually, press TRACK INCR(ement) on the remote control. For further instructions see Menu mode.
ON (AUTO): The track increments are automatically taken over from the digital source material or after 2.7 seconds silence during analogue recording.
OFF (MANUAL): While recording track numbers can be incremented manually by pressing TRACK INCR(ement) on the remote control. (Minimum track length is 4 sec.) (This can also be done in Auto track ON mode.)
• Track numbers cannot be changed after recording.
Note: Auto track works only with Consumer Sources with a digital output signal according to the IEC 958 (consumer part) audio standard.
3 With the recorder stopped, press
➜MANUAL starts to flash and the display shows REC EXT MAN followed by WAIT. After a few seconds PRESS RECORD followed by the remaining time and track number appear on the display.
REM REC | TIME TRACK | TOTAL REM | TRACK TIME | STEP |
SYNC MANUAL |
| RECORD |
| PROG |
DIGITAL I | CD | CHANGER | CD | SHUFFLE ALL |
OPTICAL I | RW |
| RW | REPEAT |
ANALOG |
| SCAN TRACK | ||
|
|
|
4 Play the source first to set the optimal recording level on the CD recorder.
5 Rotate the EASY JOG/ENTER key until, on the Record/Play Level bar, all the blue segments are alight, but the red segments do not light continuously during the loudest passages.
➜Display shows _XX DB (Decibel, e.g.
6 Stop the source.
Start manual recording
1 To start recording, press
➜
lights continuously. The track number and recording time left appear on the display.
•If CHECK INPUT message also flashes, the digital connection is incorrect.
•To record a
•To check the total remaining recording time, press DISPLAY on the CD recorder. (This can also be done during the recording.)
2 To stop recording, press STOP on the CD recorder.
➜ UPDATE lights up and 
goes out.
•If STOP was pressed within 3 seconds after RECORDING- RECORD, no recording will take place.
•To interrupt recording, press PAUSE on the CD recorder.
starts to flash. Press PAUSE again to restart recording. ( A new track will always be made.)
After recording the display will show UPDATE for several seconds.
Note: With AUTO TRACK ON, the recorder will stop and go to REC STANDBY for 1 minute and then goes to Stop mode automatically. Recordings from DAT, DCC or recordings made analogously will stop after 20 seconds silence. With AUTO TRACK OFF, the auto stop mode is disabled.
Important:
If you want to play the recorded CDR disc on any regular CD player, it must first be finalised. See finalising discs.
Finalised CDRW discs play only on CDRW compatible CD players.
English
19