Features

Selecting a track and searching

Selecting a track during playback

•Briefly press ∞ or § once or several times to skip to the current, previous or next track.

y Playback continues with the selected track, and

the track’s number is displayed.

Selecting a track when playback is stopped

1Briefly press ∞ or § once or several times to select the desired track. The track number is displayed.

2Press 2; to start CD play.

y Playback starts with the selected track.

Searching for a passage during playback

1 Keep ∞ or § pressed to find a particular passage in

FEATURES

Selecting different playing possibilities−MODE

It is possible to play tracks in random order, to repeat a single track or the entire CD, and to play the first few seconds of each track.

1Press MODE during playback as often as required in

order to activate one of the following ‘modes’. The active mode is shown in the display.

y shuffle : All tracks of the CD are played in random order until all of them have been played once.

y shuffle repeat all : All tracks of the CD are played repeatedly in random order.

y repeat : The current track is played repeatedly.

yrepeat all : The entire CD is played repeatedly.

y SCAN: The first 10 seconds of each of the remaining tracks are played in sequence.

repeat all

a backward or forward direction.

y Searching starts while playback continues at low

2 Playback starts in the chosen mode after 2 seconds.

shuffle

volume. After 2 seconds the search speeds up.

2 Release the button when you reach the desired passage.

y Playback continues from this position.

Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible.

•To return to normal playback, press MODE repeatedly until the display shows no active modes.

ESP / Power Save Mode

With a conventional portable CD-player you might have experienced that the music stopped e.g. when you were jogging. The ELECTRONIC SKIP PROTECTION prevents loss of sound caused by light vibrations and shocks. Continuous playback is ensured. However ESP does not prevent playback interruptions during vigorous running. It also does not protect the unit against any damage caused by dropping!

•Switch the slider to ESP ON during playback to activate the shock protection.

y is shown and the protection is activated.

•To deactivate the shock protection and enter the power save mode, switch the slider to POWER SAVE.

y goes off.

Programming track numbers

You can store up to 30 tracks to play in a program. A single track may be stored more than once in the program.

1 While playback is stopped, select a track with

∞or §.

2Press PROG to store the track.

y program lights up; the track number programmed and P with the total number of stored tracks are displayed.

program

3 Select and store all desired tracks in this way.

4Press 2; to start playback of your selected tracks.

yprogram is shown and playback starts.

• You can review the program by pressing PROG for

more than 2 seconds.The display shows all the stored program tracks in sequence.

yDisplay NO Prog if no tracks programmed.

Notes: – If you press PROG and there is no track selected or no tracks pro- grammed, SEL or NO PRogis displayed.

– If you try to store more than 30 tracks, FULL is displayed.

Clearing the program

• While playback is stopped, press 9 to clear program.

program

y CLRis displayed once, program goes off, and the program is cleared.

Note: The program will also be cleared if the power supply is interrupted, or if the CD-player lid is opened, or if the set switches off automatically.

RESUME and HOLD

You can interrupt playback and continue (even after an extended period of time) from the position where

playback stopped (RESUME) and you can lock all buttons	SAVE
of the set so that no action will be executed (HOLD).	POWER
Use the OFF–RESUME–HOLD slider for these functions.	ON
	ON
	ESP

RESUME – continuing from where you have stopped

1Switch the slider to RESUME during playback to activate RESUME. y resume is shown.

2Press 9 whenever you want to stop playback.

3Press 2; whenever you want to resume playback.

y resume is shown and playback continues from where you have stopped.

resume

•To deactivate RESUME, switch the slider to OFF. y resume goes off.

HOLD – locking all buttons

You can lock the buttons of the set by switching the slider to HOLD. Now, when a key is pressed, no action will be executed. This is of use, for example, when transporting the player in a bag. With HOLD activated, you can avoid accidental activation of other functions.

1 Switch the slider to HOLD to activate HOLD.

hold

y All buttons are locked HoLd is shown when you press any button. If the set is switched off,

HoLd will be shown only when 2; is	resume
pressed.
pressed.

2To deactivate HOLD, switch the slider to OFF.

Note: If you deactivate HOLD by switching the slider to RESUME, you will be activating the RESUME function.