Haier AS12GS1ERA Parts and Functions, Loading of the battery, Indoor Unit Remote controller

Parts and Functions

Indoor Unit Remote controller

Inlet

Inlet grille

Nano-Aquo Generator （inside）

Outlet

Air Purifying FilterAnion generator

(inside)

Vertical blade

(adjust left and right air flow)

Horizontal flap

(adjust up and down air flow Don't adjust it manually)

1	6	6. TIMER OFF display
2		TIMER ON display
	7	7. TEMP display
3		8. Additional functions display
4		Supplemented
		electrical	HEALTH TURBO
		Operation mode QUIET SLEEP heating
5	8	Remote controller
		9. TURBO/QUIET button
9
TURBO/QUIET	18	10. FAN button

Display board

Aureole			TEMP display
Display mode，the aureole display different
colour when setting different function
COOL: blue	FAN: yellow
AUTO: white DRY: cyan		Nano-Aquo : green
	Inlet	Air Purifying Filter (inside)
Inlet grille
Outlet
Horizontal flap	Vertical blade			Emergency
				Switch
(adjust up and down air flow	(adjust left and		Display board
Don't adjust it manually)	right air flow)
Display board	1	2	3	4	5

10			19	11.	COOL button
11				12. SWING LEFT/RIGHT button
			20
				13. FAN SPEED button
12
	SWING		21	14.	HEALTH display
13				15.	SLEEP display
			22	16.	LOCK button
14	HEALTH	SLEEP		17.	LIGHT button
			23
15				Control the lightening and extinguishing
	TIME	TIME
	ON	OFF
16			24	of the indoor LED display board.
				18. POWER/SOFT display
17			25
				19.	DRY button
				20. TEMP display
				21.SWING UP/DOWN button
1. Mode display				22. TIMER OFF/ON displa
Operation mode	AUTO COOL DRY		FAN	23.HEALTH AIR FLOW button
Remote controller				24.CANCEL/CONFIRM button
2. Signal sending display
				Function: Setting and cancel to the
3. SWING	display			timer and other additional functions.
4. FAN SPEED display				25.	RESET button
			Display	When the remote controller appears
			circulated	abnormal, use a sharp pointed
LO MED		HI	AUTO	article to press this button to reset

1Signal receiver hole

2ON/OFF display

3Ambient temp.display

When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed.

4TIMER ON\OFF display TIMER ON-OFF display

SLEEP display

Note to the power failure resume:

press the sleep button ten times in five seconds and enter function after hearing four sounds.And press the sleep button ten times within five seconds and leave this function after hearing two sounds.

5COOL\HEAT\Dry\AUTO display

5. LOCK display the remote.

Healthy function is not available for some units.

Outdoor Unit

OUTLET

INLET

CONNECTING PIPING

	1	Inlet	54 Air Purifying Filter (inside)
2 Inlet grille					8
					Emergency
					Switch
3	Outlet				9
45	Anion generator	6 Vertical blade		12	10
					11
	(inside)	(adjust left and
7	Horizontal flap				13
			right air flow)
(adjust up and down air flow

Don't adjust it manually)

9Power indicator (Lights up when unit starts.)

10 Timer mode indicator

(Lights up whenTimer operation is selected.)

11 Operation mode indicator

(lights up when the compressor is on.)

12Remote signal receiver

(A beeping sound is generated when a signal from remote controller isreceived.)

13 Ambient temp display

When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference.

Actual inlet grille may vary from the one shown in the manual according to the product purchased

2

	4	AND ELECTRICAL WIRING
		4 DRAIN HOSE
Loading of the battery
1	Remove the battery cover;
2	Load the batteries as illustrated.
	2 R-03 batteries, resetting key
3	(cylinder);
	Be sure that the loading
	is in line with the" + "/"-";

Note: 4 Load the battery,then put on the cover again.

The distance between the signal transmission head and the rece- iver hole should be within 7m without any obstacle as well.

When electronic-started type fluorescent lamp or change- over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receiving the signals, so the distance to the indoor unit should be shorter.

Full display or unclear display during operation indicates the batteries have been used up. Please change batteries.

If the remote controller can't run normally during operation, please remove the batteries and reload several minutes later.