Giant P200A-3100/5100, Triplex Ceramic Plunger Pump Installation Instructions

Page 2

INSTALLATION INSTRUCTIONS

Installation of the Giant Industries, Inc., pump is not a complicated procedure, but there are some basic steps common to all pumps. The following information is to be considered as a general outline for installa- tion. If you have unique requirements, please contact Giant Industries, Inc. or your local distributor for assistance.

1.The pump should be installed flat on a base to a maximum of a 15 degree angle of inclination to ensure optimum lubrication.

2.The inlet to the pump should be sized for the flow rate of the pump with no unnecessary restrictions that can cause cavitation. Teflon tape should be used to seal all joints. If pumps are to be operated at temperatures in excess of

1200 F, it is important to insure a positive head to the pump to prevent cavitation.

3.The discharge plumbing from the pump should be properly sized to the flow rate to prevent line pressure loss to the work area. It is essential to provide a safety bypass valve between the pump and the work area to protect the pump from pressure spikes in the event of a blockage or the use of a shut-off gun.

4.Use of a dampener is necessary to minimize pulsation at drive elements, plumbing, connec- tions, and other system areas. The use of a dampener with Giant Industries, Inc. pumps is optional, although recommended by Giant Industries, Inc. to further reduce system pulsa- tion. Dampeners can also reduce the severity of pressure spikes that occur in systems using a shut-off gun. A dampener must be positioned downstream from the unloader.

5.Crankshaft rotation on Giant Industries, Inc. pumps should be made in the direction desig- nated by the arrows on the pump crankcase. Reverse rotation may be safely achieved by following a few guidelines available upon request from Giant Industries, Inc. Required horsepower for system operation can be obtained from the charts on pages 3-7.

6.Before beginning operation of your pumping system, remember: Check that the crankcase and seal areas have been properly lubricated per recommended schedules. Do not run the pump dry for extended periods of time. Cavitation will result in severe damage. Always remember to check that all plumbing valves are open and that pumped media can flow freely to the inlet of the pump.

Finally, remember that high pressure operation in a pump system has many advantages. But, if it is used carelessly and without regard to its potential hazard, it can cause serious injury.

IMPORTANT OPERATING CONDITIONS

Failure to comply with any of these conditions invalidates the warranty.

1.Prior to initial operation, add oil to the crank- case so that oil level is between the two lines on the oil dipstick. DO NOT OVERFILL.

For P218A, P219A and P220A, use Giant Industries, Inc. oil (part # 01060) or the equivalent Kendall Turbo GT1 (20w-50) oil may be used. For P217A use Giant Oil (part #01150) or Mobil 1 (15W-50).

Crankcase oil should be changed after the first 50 hours of operation, then at regular intervals of 500 hours or less depending on operating conditions.

2.Pump operation must not exceed rated

pressure, volume, or RPM. A pressure relief device must be installed in the discharge of the system.

3.Acids, alkalines, or abrasive fluids cannot be pumped unless approval in writing is obtained before operation from Giant Industries, Inc.

4.Run the pump dry approximately 10 seconds to drain the water before exposure to freezing temperatures.

Image 2
Contents Contents P200A-3100/5100Installation Instructions Specifications Model P217A-3100/5100 P217A-3100/5100 HorsepowerSpecifications Model P218A-3100/5100 P218A-3100/5100 HorsepowerSpecifications Model P219A-3100/5100 P219A-3100/5100 HorsepowerModel P220A-3100/5100 SpecificationsP220A-3100/5100 Horsepower P221A-3100 Horsepower Requirements P200A-3100/5100 Series Parts List Position Item# DescriptionExploded View P200A-3100/5100 Series Repair Instruction P200A-3100/5100 Series Repair Instruction P200A-3100/5100 Series Giant Industries Limited Warranty P200A-3100/5100 Dimensions mm
Related manuals
Manual 12 pages 56.5 Kb Manual 12 pages 22.84 Kb

Triplex Ceramic Plunger Pump, P200A-3100/5100 specifications

The Giant Triplex Ceramic Plunger Pump is a cutting-edge solution designed to meet the demanding needs of high-pressure applications in various industries. Known for its durability and efficiency, this pump provides reliable service in tasks such as pressure washing, industrial cleaning, and other high-flow, high-pressure operations.

One of the standout features of the Giant Triplex Ceramic Plunger Pump is its triplex design. Unlike traditional single-piston pumps, the triplex configuration uses three plungers that work in a staggered sequence. This results in smoother operation, reduced pulsation, and improved overall performance. The synchronized action of the plungers ensures that fluid delivery is constant and consistent, which is crucial for applications requiring high pressure.

The pump is equipped with ceramic plungers, which are engineered to withstand abrasive materials and harsh chemicals. These ceramic components offer exceptional resistance to wear and tear, extending the lifespan of the pump and reducing maintenance costs. This durability is especially beneficial in industrial settings where the pump may encounter contaminants or abrasive substances.

Another technological advancement found in the Giant Triplex Ceramic Plunger Pump is its built-in unloader valve. This crucial component protects the pump from excessive pressure buildup, allowing for safe and efficient operation. In situations where the pressure exceeds pre-set limits, the unloader valve automatically diverts or bypasses the flow, preventing potential damage to the pump and other connected equipment.

Additionally, the Giant Triplex pump features a brass head construction that enhances its strength and robustness. This design also allows for better heat dissipation, ensuring that the pump operates efficiently even under high-pressure conditions. The incorporation of high-quality seals and O-rings enhances the pump's reliability by preventing leaks and ensuring optimal performance over time.

Overall, the Giant Triplex Ceramic Plunger Pump is renowned for its high efficiency, longevity, and robustness. These characteristics make it an ideal choice for various high-pressure applications across industries. Its advanced technologies, including the triplex design, ceramic plungers, built-in unloader valve, and robust construction, provide users with a reliable and effective pumping solution that meets the challenges of modern industrial demands. Whether for pressure washing, cleaning, or other demanding applications, this pump stands out as an essential tool for professionals seeking performance and durability.