GENERAL INFORMATION / CD PLAY
In-car use (connections supplied or optionally available)
Only use the AY 3545 (4822 219 10033) or AY 3548 (3140 118 71890) car voltage converter (4.5 V DC, positive pole to the center pin) and the AY 3501 cassette car adapter. Any other product may damage the set.
1Put the set on a horizontal,
stable surface. Make sure it is in a safe place, | 12 V DC |
where the set is neither a danger nor an |
|
obstacle to the driver and the passengers. |
|
2Plug the voltage converter into the
cigarette lighter jack (only for 12 V car | 4,5 V DC |
battery, negative grounding), then connect |
|
the wired end with 4.5V DC input jack on the |
|
set. |
|
3If necessary, clean the cigarette lighter jack to obtain a good electrical contact.
4Turn down the volume and connect the cassette adapter plug to LINE OUT/p on the set.
5Carefully insert the cassette adapter into the car radio’s cassette compartment.
6Make sure the cord does not hinder your driving.
7Set VOL E on the set to position 8. Start playback on the set and adjust the sound with the car radio controls.
•Always remove the voltage converter from the cigarette lighter jack- when the set is not in use.
Note: If your car radio has a LINE IN jack, it is better to use it for the
car radio connection instead of the cassette.adapter. Connect the signal lead to this LINE IN jack and to LINE OUT/pon the set.
Playing a CD
CD PLAY / FEATURES
Playback information
•If a
•When playing a
•Playback will stop if you open the CD lid.
•While the CD is read, 1
Volume and bass
Volume adjustment
• Adjust the volume by using VOL E.
Bass adjustment
• Press BASS to switch the bass enhancement on or off
y 
is shown if the bass enhancement is acti- vated.
Remote control (supplied or optionally available)
Use the AY 3767 or AY 3768 cord remote control.The buttons on the remote control have the same functions as the corresponding buttons on the set.
1Press 9 twice to switch off the set.
2Firmly connect the remote control to LINE OUT/pon the set.
3Adjust the volume VOL E on the CD player and remote control.
Selecting a track and searching
This
1Push the OPEN 2 slider to open the player.
2Insert an audio CD, printed side up, by pressing the CD onto the hub.
3Close the player by pressing the lid down.
4Press 2; to switch the player on and start playback. yThe current track number and elapsed playing
time are displayed.
•You can pause playback by pressing 2;.
yThe time at which playback was paused starts flashing.
•You can continue playback by pressing 2; again.
5Press 9 to stop playback.
yThe total number of tracks and the total playing time of the CD are displayed.
6Press 9 again to switch the player off.
•To remove the CD, hold it by its edge and press the hub gently while lifting the CD.
Note: If there is no activity, the set will automatically switch off after a while to save energy.
OLD
LINE OUT/
VO
L.
Selecting a track during playback
• Briefly press ∞ or § once or several times to skip to the current, previous or next track.
yPlayback continues with the selected track, and the track’s number is displayed.
Selecting a track when playback is stopped
1Briefly press ∞ or § once or several times to select the desired track. The track number is displayed.
2Press 2; to start CD play.
yPlayback starts with the selected track.
Searching for a passage during playback
1Keep ∞ or § pressed to find a particular passage in a backward or forward direction.
ySearching starts while playback continues at low volume. After 2 seconds the search speeds up.
2Release the button when you reach the desired passage. yPlayback continues from this position.
Notes: – If the player is in SCAN mode (see MODE chapter), searching is not possible.
–In SHUFFLE, SHUFFLE REPEAT ALL or REPEAT mode (see MODE chapter), or while playing a program, searching is only possible within the particular track.