English
Using the Cassette Deck (Recording)
TAPE @ #
7
REMOTE CONTROL
DIMMER SLEEP
DISPLAY FM MODE MD/AUX
AHB PRO | AUTO | CD |
PRESET | ||
PROGRAM RANDOM | REPEAT | |
BASS | TREBLE | CANCEL |
UP
SET
DOWN
PTY/EON |
| DISPLAY MODE |
TAPE | TUNER | CD |
| BAND |
|
| VOLUME |
|
| STANDBY/ON |
|
|
|
|
| MD/ |
|
| AHB |
|
| AUX |
|
| PRO |
|
|
|
|
| VOLUME |
|
| REC |
|
| TIMER |
|
REC | REV |
|
|
|
|
MODE |
|
| CLOCK |
| |
REV. MODE |
|
|
| OPEN/CLOSE |
|
|
|
|
| CD |
|
TAPE @ # | TAPE | FM/AM | CD | CD #/8 |
|
DOWN | MULTI CONTROL | UP |
| ||
| PHONES |
|
|
|
|
7 |
|
|
|
| Tape Direction indicator |
|
|
|
|
| |
CD #8 |
|
|
| REC indicator |
|
|
|
|
| REC |
When the System is in use, the display shows other items as well.
For simplicity, only the items described in this section are shown here.
Reverse Mode indicator
Recording onto a tape from any of the sound sources is simple. Just | Standard Recording | ||
place a tape in the Cassette Deck, have the source ready, make one | |||
or two settings, and you’re ready to record. For each source the | You can record any sound source to tape as follows: | ||
procedure is a little bit different so we explain each separately. But | |||
|
| ||
first, here are a few things to make your recordings better. |
| Insert a blank or erasable tape into the | |
1 | |||
|
| Cassette Deck. | |
Things to know before you start recording –––––––––––––––––––––––––––––
■ It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.
■ When you want to record onto both sides of a tape, you can set Reverse mode to do so. Recording automatically stops after recording in the 2direction. Therefore, make sure that the tape direction is 3when recording with Reverse mode on.
■ The recording level, which is the volume at which the new tape is being made, is automatically set correctly, so it is not affected by the VOLUME control on the System. Nor is it affected by adjusting the sound effects. Thus, during recording you can adjust the sound you are actually listening to without affecting the recording level.
■ Two small tabs on the back of the cassette tape, one for side A and one for side B, can be removed to prevent accidental erasure or recording.
■To record on a cassette with the tabs removed, you must cover the holes with adhesive tape first. However, when a type II tape is used, only cover part of the hole as shown, since the other part of the hole (Type II detection slot) is used to detect the tape type.
■Type I and Type II tapes can be used for recording.
Note: At the start and end of cassette tapes, there is leader tape which cannot be recorded onto. Thus, when recording CDs or radio broadcasts, wind on the leader tape first to ensure that the recording will be made without any music part lost.
CAUTION:
If a recording you make has excessive noise or static, the Unit may have been too close to a TV which was on during the recording. Either turn off the TV or increase the distance between the TV and the System.
2If you want to record on both sides of a tape, press the REV. MODE button on the Unit until the 
indicator is lit.
•When using Reverse mode, insert the tape so that it will be recorded in the forward 3direction.
3Check the recording direction for the tape.
Make sure that the Tape Direction indicator is the same as that for the tape in the Cassette Deck. If the directions are different, press the TAPE @#button to correct the tape direction and then press the 7button to stop the tape.
4Prepare the source by, for example, tuning in a radio station or turning on
connected auxiliary equipment.
Note: For CD recording, refer to “CD Direct Recording” on page 17.
5Press the REC button on the Unit.
The REC indicator lights up and the System begins recording.
Notes for using Reverse mode for recording
When recording in Reverse mode, the System automatically stops when it reaches the end of the reverse 2direction. To record on both sides of a tape, make sure that the recording direction for the tape inserted is forwards 3, and that the Tape Direction indicator is also forwards 3, before you start recording.
To stop at any time during the recording process
Press the 7 button.
16