Haier FCD-JTHMG50-III, FCD-JTHMG60-III, FCD-JTHMG80-III, FCD-JTHMG100-III user manual Dimensions

Operation Instructions

2.Temperature Setting

With the machine powered on (with no any digits flashing on the display), press or

Dimensions

(Fig.1)

button to enter temperature setting status with the temperature digits rapidly flashing. Temperature can be changed between 35 - 75 with an increment 1 . In real-time heating mode, you can directly press or button to adjust temperature setting value. In

medium warm status, machine defaulted highest temperature is 40 and can't be adjusted. If actual water temperature is lower than setting value and the machine is in medium warm mode, you need to change operation mode to real-time heating mode, and then the machine can heat water to the set temperature.

3.Clock Calibration

Clock goes in 24-hour and 60-min system in a second flashing way. Example: calibrate the clock to 11:29

After powering on, in real-time heating and night power modes, you can press Set button

Front View

a1

1b

C1

Bottom View

I A B

1d

I: Drain

to enter clock calibration status with hour digits flashing. Press or button to set 11.

Press Set button again and minute digits flash. Press or button to set 29. You can press Set button to confirm current setting, or wait 6 s after which the system will automatically confirms and quits setting status (as shown in Fig. 7, machine is in real-time heat / warm mode).

HEATING

	ACTUAL
Fig.6	Fig.7

4. Power Level Selection

With the machine powered on, press Power button to directly go to power level selection status. You can select a power level 850 W, 1300 W or 2150 W. If 850 W is selected, 850 W digits are lighted and only the upper heating element works. If 1300 W is selected, 1300 W digits are lighted and only the lower heating element works. If 2150 W is selected, 2150 W digits are lighted and both the upper and lower heating elements work. In Delay mode, machine defaulted heating power is 2150 W and can't be adjusted. Fig. 8 shows a heating power level 2150 W, the present clock time 12:10, and the real-time heating mode.

5.Real-time Heat / Warm Setting

With machine powered on, as described in Item 10, press Mode button to enter Real-time Heat / Warm mode with real-time heat indication lighted on. According to settings, machine will automatically starts to heat or keep warm. The machine has a thermostat function, by which, the machine goes into warm keeping status when it reaches the temperature setting value. In warm keeping status, machine automatically starts heating when actual water temperature is 5 (for setting value lower than 55 ) or 10 (for setting value equal to or above 55 ) lower than the setting value, until reaching setting temperature again. It repeats in this way.

Example: Fig. 9 shows real-time heat / warm status with heating power 1300W and temperature setting 75 .

HEATING SET HEATING

ACTUAL

Fig.8 Fig.9

6.Medium Warm Setting

With machine powered on, as described in Item 10, press Mode button until it enters Medium Warm operation mode (with Medium Warm indication on the display).

Model		Volume	Net	a1	b1	c1	d1
			Weight
FCD-JTHMG50-	E	50L	22kg	671mm	442mm	100mm	410mm
FCD-JTHMG60-	E	60L	25kg	765mm	442mm	100mm	410mm
FCD-JTHMG80-	E	80L	29kg	876mm	479mm	100mm	450mm
FCD-JTHMG100-	E	100L	34kg	1052mm	479mm	100mm	450mm

Remarks:the permitted error limit of above parameters is 10%.

Attentions in installation

During installation, adequate space must be reserved for future maintenance and repair. If the water heater is installed within decoration boards, the right board shall be removable to facilitate removing the plastic cover during maintenance.

City water inlet pressure shall not be less than 0.05 Mpa.

Electric water heater shall be installed indoors with ambient temperature above 0 . The pipes shall be collectively laid. Hot water outlet shall not be too far from use points. In case farer than 8 m, hot water pipe shall have a thermal insulation to minimize heat loss.

The mounting wall shall be firm and reliable to support twice the weight of water heater full of water. Non-load bearing walls or air brick walls must have corresponding protective measures like additional support, wall-through screws or back boards.

Electric water heater shall be located in a place easy for use, maintenance and with a floor drainer. In case the tank or pipes leak, nearby or lower facilities shall not be damaged. The installation location shall avoid being above toilet bowl, bathtub, washbasin or doorframe, where will cause a suppressed or unsafe feeling to users.

Power socket for water heater shall be in a dry place free of water splash to avoid nonnormal work of the water heater. (splash-proof box is preferred)

Do not confuse inlet and outlet water pipes. Safety valve shall be installed at designated position with no random modification. The safety valve pressure relief vent shall keep open to the air. Do not block it.

To ensure safety, water heater shall use a separate socket (not multi-purpose socket) and be reliably grounded. Socket quality shall comply with local standard. Check with a neo-electroscope the line and neutral are not wrongly connected. Only after confirming the tank is full of water, no water leakage at various connections and power supply meets requirements, power can be turned on to start heating.