Graco 308116T important safety instructions Displacement Pump Service, Disassembly, Reassembly

Page 13

Service

Displacement Pump Service

Disassembly

When disassembling the pump, lay out all removed parts in sequence, to ease reassembly. Refer to Fig 5.

NOTE: Standard Repair Kit 224401 (UHMWPE/PTFE packings) is available. For the best results, use all the new parts in the kit. Parts included in the kit are de- noted with one asterisk, for example (3*).

Conversion Kit 224889 is available to convert the pump to all PTFE packings. See page 19 for details.

Clean all the parts thoroughly when disassembling. Check them carefully for damage or wear, replacing parts as needed.

1.Remove the displacement pump from the air motor as explained on page 12.

2.Unscrew the locking ring (7) from the cylinder (8). See Fig 5. Remove the intake valve housing (15).

3.Remove the o-ring (12), ball stop pin (6), ball guide

(9)and ball (4) from the intake valve housing (15).

4.Loosen the packing nut (2). Push the displacement rod (13) down as far as possible, then pull it out the bottom of the cylinder (8).

5.Secure the flats of the displacement rod (13) in a vise. Using a wrench on the flats of the piston mounting stud (28), screw the piston off the rod. Remove one cotter pin (3) and the ball stop pin (21), taking note which set of holes it is in. Then remove the ball (4).

6.Place the flats of the piston mounting stud (28) in a vise, and unscrew the piston stud (26). Remove the piston packings (20, 23), glands (25, 27), washer (19), and shims (31).

7.Remove the packing nut (2), throat packings (5, 24), and glands (11, 14) from the outlet housing

(1).

8.Inspect all parts for damage. Clean all parts and threads with a compatible solvent before reassem- bling. Inspect the polished surfaces of the dis- placement rod (13) and cylinder (8) for scratches, scoring or other damage, which can cause prema- ture packing wear and leaking. To check, run a finger over the surface or hold the part up to the light at an angle. Be sure the ball seats of the piston (26) and intake valve housing (15) are not chipped or nicked. Replace any worn or damaged parts.

Reassembly

NOTE: On UHMWPE/PTFE packed pumps, the packing order is one UHMWPE packing, two PTFE packings, and one UHMWPE packing. On PTFE packed pumps, all four packings are PTFE.

1.See Fig 5 and the NOTE above. Lubricate the throat packings and install them in the outlet housing (1) one at a time as follows, with the lips of the v-packings facing down: the male gland (11*), the v-packings (24* or 5*), and the female gland (14*). Apply thread lubricant and install the packing nut (2) loosely.

2.If you removed the cylinder (8), apply thread lubricant and reinstall it in the outlet housing (1), making sure to replace the o-ring (10).

3.See Fig 5 and the NOTE above. Install shims (31*) onto the piston stud (26) as required to eliminate end play. Lubricate the piston packings and install them one at a time in the following order, with the lips of the v-packings facing up: the female gland (25*), the v-packings (23* or 20*), the male gland (27*), and the washer (19*).

4.Apply thread sealant and screw the piston stud

(26) onto the piston mounting stud (28). Torque to 50--70 ft-lb (68--95 NSm). Install the piston ball (4*) on the piston seat. Slide the ball stop pin (21*) into the desired set of holes, and secure with the cotter pin (3*).

5.Place the flats of the displacement rod (13) in a vise. Apply sealant and screw the piston assembly onto the displacement rod. Torque to 50--70 ft-lb (68--95 NSm).

6.Insert the displacement rod (13) into the bottom of the cylinder (8), being careful not to scratch the cylinder. Push the rod straight up until it protrudes from the packing nut (2).

7.Install the ball (4*), guide (9), o-ring (12), and ball stop pin (6*) in the intake valve housing (15). Place the intake valve assembly in the locking ring (7). Apply thread sealant to the locking ring and cylin- der (8), and screw the ring onto the cylinder.

8.Reconnect the displacement pump to the air motor as explained on page 12.

308116 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Important Safety Instructions Instructions--Parts ListRatio Presidentr Pump Ratio Monarkr PumpSymbols Table of ContentsSurgical treatment Skin Injection HazardFire and Explosion Hazard KEY Typical InstallationGeneral Information InstallationPrepare the Operator Grounding Mounting the PumpMounting Accessories System AccessoriesAir Line Accessories Air and Fluid HosesPressure Relief Procedure Operation/MaintenanceFlush the Pump Before First Use Shutdown and Care of the Pump Starting and Adjusting the PumpAir Motor Plate Problem Cause Solution TroubleshootingRelieve the pressure Disconnecting the Displacement Pump ServiceReconnecting the Displacement Pump Follow the Pressure Relief Procedure onDisassembly Displacement Pump ServiceReassembly Detail B Piston Packings Detail a Throat PackingsModel 224342, Series a PartsPart Description Qty Model 261630, Series a Model 224343, Series a shownModel 247147, Series a Model 902147, Series a shownModel 254999, Series a Model 224341, Series a shownOptional Ptfe Packing Conversion Model 224341, Series aKit Description QtyModel 15G976, Series a Parts President Technical DataCategory Data Monark Layout Dimensions Mounting HoleModel 224342 Shown Pump Model308116 Graco Information Graco Standard Warranty

308116T specifications

The Graco 308116T is an advanced airless paint sprayer designed for both professional and DIY users, ideal for tackling a variety of painting tasks with precision and efficiency. This model exemplifies Graco’s commitment to innovation and user-friendliness, providing exceptional performance for projects of all sizes.

One of the standout features of the Graco 308116T is its TrueAirless Technology, which allows users to spray directly from the paint can without the need for thinning. This feature not only saves time but also ensures a smooth and even application of paint, allowing for a professional finish. With a maximum pressure of 3,000 PSI, this sprayer is capable of handling a wide range of coatings, including heavier materials, making it suitable for both residential and commercial applications.

The Graco 308116T also boasts an adjustable spray pattern, enabling users to switch between a wide fan pattern for larger surfaces and a narrower pattern for detailed work. This versatility is enhanced by the innovative RAC IV SwitchTip technology, which allows users to reverse the tip for easy clog clearance, minimizing downtime and frustration during projects.

In terms of portability, the Graco 308116T is equipped with a lightweight yet durable frame, ensuring easy transport and mobility on job sites. The integrated carrying handle adds to its convenience, making it easy to maneuver around different areas as needed.

Another significant characteristic of the Graco 308116T is its high-efficiency airless pump. This advanced pump design delivers consistent pressure and a steady flow of paint, improving productivity and reducing paint waste during application. The unit is also designed for easy clean-up after use, with a simple system that allows for quick flushing of the paint system.

Additionally, durability is a key aspect of the Graco 308116T. Constructed with high-quality materials, it is built to withstand the rigors of frequent use while maintaining performance over time. Its robust design makes it suitable for a wide range of applications, from painting walls and ceilings to tackling outdoor projects.

Overall, the Graco 308116T airless paint sprayer combines advanced technology with user-friendly features, delivering exceptional performance and versatility. Whether you’re a seasoned professional or a DIY enthusiast, this sprayer is an excellent choice for achieving flawless finishes with ease.
Top Page Image Contents