Graco 308116T Operation/Maintenance, Pressure Relief Procedure, Flush the Pump Before First Use

Page 8

Operation/Maintenance

Pressure Relief Procedure

WARNING

PRESSURIZED EQUIPMENT HAZARD

The system pressure must be manually relieved to prevent the system from starting or spraying acci- dentally. To reduce the risk of an injury from acci- dental spray from the gun, splashing fluid, or moving parts, follow the Pressure Relief Proce- dure whenever you:

Dare instructed to relieve the pressure, D stop spraying,

D check or service any of the system equipment, D or install or clean the spray tip.

1.Lock the spray gun safety latch.

2.Shut off the air supply to the pump.

3.Close the bleed-type master air valve (required in your system).

4.Unlock the gun safety latch.

5.Hold a metal part of the gun firmly to the side of a grounded metal pail, and trigger the gun to relieve pressure.

6.Lock the gun safety latch.

7.Open the drain valve (required in your system), having a container ready to catch the drainage.

8.Leave the drain valve open until you are ready to spray again.

If you suspect that the spray tip or hose is completely clogged, or that pressure has not been fully relieved after following the steps above, very slowly loosen the tip guard retaining ring or hose end coupling and relieve pressure gradually, then loosen completely. Now clear the tip or hose.

WARNING

Moving parts can pinch or amputate your fingers or other body parts. When air is supplied to the motor, the air motor piston (located behind the air motor plates) moves. See Fig. 3. Therefore, never oper- ate the pump with the air motor plates removed.

Flush the Pump Before First Use

The pump is tested with lightweight motor oil, which is left in to protect the pump parts. If the fluid you are using may be contaminated by the oil, flush it out with a compatible solvent before using the pump. If the pump is being used to supply a circulating system, allow the solvent to circulate until the pump is thor- oughly flushed.

WARNING

For your safety, read the warning section, Fire or Explosion Hazard, on page 4 before flushing, and follow all the recommendations given there.

8 308116

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Instructions--Parts List Important Safety InstructionsRatio Presidentr Pump Ratio Monarkr PumpTable of Contents SymbolsSkin Injection Hazard Surgical treatmentFire and Explosion Hazard Typical Installation KEYInstallation General InformationPrepare the Operator Grounding Mounting the PumpSystem Accessories Mounting AccessoriesAir Line Accessories Air and Fluid HosesFlush the Pump Before First Use Operation/MaintenancePressure Relief Procedure Starting and Adjusting the Pump Shutdown and Care of the PumpAir Motor Plate Relieve the pressure TroubleshootingProblem Cause Solution Service Disconnecting the Displacement PumpReconnecting the Displacement Pump Follow the Pressure Relief Procedure onReassembly Displacement Pump ServiceDisassembly Detail a Throat Packings Detail B Piston PackingsPart Description Qty PartsModel 224342, Series a Model 224343, Series a shown Model 261630, Series aModel 902147, Series a shown Model 247147, Series aModel 224341, Series a shown Model 254999, Series aModel 224341, Series a Optional Ptfe Packing ConversionKit Description QtyModel 15G976, Series a Parts Category Data Technical DataPresident Monark Dimensions Mounting Hole LayoutModel 224342 Shown Pump Model308116 Graco Standard Warranty Graco Information

308116T specifications

The Graco 308116T is an advanced airless paint sprayer designed for both professional and DIY users, ideal for tackling a variety of painting tasks with precision and efficiency. This model exemplifies Graco’s commitment to innovation and user-friendliness, providing exceptional performance for projects of all sizes.

One of the standout features of the Graco 308116T is its TrueAirless Technology, which allows users to spray directly from the paint can without the need for thinning. This feature not only saves time but also ensures a smooth and even application of paint, allowing for a professional finish. With a maximum pressure of 3,000 PSI, this sprayer is capable of handling a wide range of coatings, including heavier materials, making it suitable for both residential and commercial applications.

The Graco 308116T also boasts an adjustable spray pattern, enabling users to switch between a wide fan pattern for larger surfaces and a narrower pattern for detailed work. This versatility is enhanced by the innovative RAC IV SwitchTip technology, which allows users to reverse the tip for easy clog clearance, minimizing downtime and frustration during projects.

In terms of portability, the Graco 308116T is equipped with a lightweight yet durable frame, ensuring easy transport and mobility on job sites. The integrated carrying handle adds to its convenience, making it easy to maneuver around different areas as needed.

Another significant characteristic of the Graco 308116T is its high-efficiency airless pump. This advanced pump design delivers consistent pressure and a steady flow of paint, improving productivity and reducing paint waste during application. The unit is also designed for easy clean-up after use, with a simple system that allows for quick flushing of the paint system.

Additionally, durability is a key aspect of the Graco 308116T. Constructed with high-quality materials, it is built to withstand the rigors of frequent use while maintaining performance over time. Its robust design makes it suitable for a wide range of applications, from painting walls and ceilings to tackling outdoor projects.

Overall, the Graco 308116T airless paint sprayer combines advanced technology with user-friendly features, delivering exceptional performance and versatility. Whether you’re a seasoned professional or a DIY enthusiast, this sprayer is an excellent choice for achieving flawless finishes with ease.
Top Page Image Contents