Graco 3A2578B Warnings, Equipment Misuse Hazard, Thermal Expansion Hazard

Page 4
EQUIPMENT MISUSE HAZARD

Warnings

THERMAL EXPANSION HAZARD WARNING

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

•Do not operate the unit when fatigued or under the influence of drugs or alcohol.

•Do not exceed the maximum working pressure or temperature rating of the lowest rated

system component. See Technical Data in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete information about your material, request MSDS from distributor or retailer.

•Do not leave the work area while equipment is energized or under pressure.

•Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

•Check equipment daily. Repair or replace worn or damaged parts immediately with genuine manufacturer’s replacement parts only.

•Do not alter or modify equipment. Alterations or modifications may void agency approvals and create safety hazards.

•Make sure all equipment is rated and approved for the environment in which you are using it.

•Use equipment only for its intended purpose. Call your distributor for information.

•Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

•Do not kink or over bend hoses or use hoses to pull equipment.

•Keep children and animals away from work area.

•Comply with all applicable safety regulations.

THERMAL EXPANSION HAZARD

Fluids subjected to heat in confined spaces, including hoses, can create a rapid rise in pressure due to the thermal expansion. Over-pressurization can result in equipment rupture and serious injury.

• Open a valve to relieve the fluid expansion during heating.

• Replace hoses proactively at regular intervals based on your operating conditions.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many solvents can degrade plastic parts and cause them to fail, which could cause serious injury or property damage.

• Use only compatible water-based solvents to clean plastic structural or pressure-containing parts.

• See Technical Data in this and all other equipment instruction manuals. Read fluid and solvent manufacturer’s MSDSs and recommendations.

4

3A2578B

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Operation Husky 2200 Air-OperatedDiaphragm Pump3A2578B Contents 3A2578BWarnings WarningsFIRE AND EXPLOSION HAZARD PRESSURIZED EQUIPMENT HAZARDPLASTIC PARTS CLEANING SOLVENT HAZARD WarningsEQUIPMENT MISUSE HAZARD THERMAL EXPANSION HAZARDWarnings TOXIC FLUID OR FUMES HAZARDBURN HAZARD PERSONAL PROTECTIVE EQUIPMENTTo Order Replacement Parts Ordering InformationRelated Manuals To Find Your Nearest DistributorConfiguration Number Matrix 2200PP01A 2200PInstallation General InformationTighten Fasteners Tips to Reduce CavitationInstallation Accessories/Components Not SuppliedSystem Components 3A2578BInstallation Ground The SystemAir Lines •Fluid supply container: Follow local codeAir Exhaust Ventilation NOTICEInstallation To provide a remote exhaustFluid Supply Line Fluid Outlet LineInstallation 3A2578BInstallation Flange Connections3A2578B Pressure Relief Procedure Start and Adjust the PumpOperation Flush the Pump Before First UseMaintenance Maintenance ScheduleLubrication Tighten Threaded ConnectionsTorque Instructions Torque InstructionsDo not overtorque Fluid Cover ScrewsNotes Notes3A2578B Dimensions End Flange Models, Polypropylene and PVDFDimensions PolypropyleneCenter Flange Models, Polypropylene Only DimensionsPolypropylene PolypropylenePerformance Charts Bolt-throughDiaphragmsFluid Pressure Air ConsumptionOvermolded Diaphragms Performance ChartsHow to Read the Charts Fluid PressureTechnical Data Technical DataHusky 2200 Diaphragm Pump Air consumptionTechnical Data WeightMaximum pump speed Wetted PartsGraco Information Graco Standard Husky Pump Warranty
Top Page Image Contents