Roof Curb Installation Rigging | Goodman Mfg SS-CPG180-240 guide

Product Specifications

Roof Curb Installation — Rigging

Provisions for forks have been included in the unit base frame. No other fork locations are approved.

•Unit must be lifted by the four lifting holes located at the base frame corners.

•Lifting cables should be attached to the unit with shackles.

•The distance between the crane hook and the top of the unit must not be less than 60”.

•Two spreader bars must span over the unit to prevent damage to the cabinet by the lift cables. Spreader bars must be of sufficient length so that cables do not come in contact with the unit during transport. Remove wood struts mounted beneath unit base frame before set- ting unit on roof curb. These struts are intended to protect unit base frame from fork lift damage. To remove the struts, extract the sheet metal retainers and pull the struts through the base of the unit. Refer to rigging label on the unit.

Important: If using bottom discharge with roof curb, duct-work should be attached to the curb prior to installing the unit. Duct-work dimensions are shown in Roof Curb Installation Instructions Manual.

Refer to the Roof Curb Installation Instructions for proper curb installation. Curbing must be installed in compliance with the National Roofing Contractors Association Manual.

Lower unit carefully onto roof mounting curb. While rigging the unit, the center of gravity will cause the condenser end to be lower than the supply air end.

Bring condenser end of unit into alignment with the curb. With condenser end of the unit resting on curb member and using curb as a fulcrum, lower opposite end of the unit until entire unit is seated on the curb. When a rectangular cantilever curb is used, take care to center the unit. Check for proper alignment and orientation of supply and return openings with duct.

40”		Compressor 1
40”

	Coil
	Coil
	Evaporator	Return
Supply		Return

Compressor 2

58”

Corner & Center-of-Gravity Locations

	15-Ton Units	Weights
	15-Ton Units	(lbs.)
		(lbs.)
	Corner Weight A	570
	Corner Weight B	535
	Corner Weight C	545
	Corner Weight D	510
	Shipping Weight	2270
	Operating Weight	2155

	20-Ton Units	Weights
	20-Ton Units	(lbs.)
		(lbs.)
	Corner Weight A	655
	Corner Weight B	535
	Corner Weight C	600
	Corner Weight D	485
	Shipping Weight	2390
	Operating Weight	2275

To assist in determining rigging requirements, unit weights are shown to the right. Note: These weights are calculated without installed accessories.

www.goodmanmfg.com

SS-CPG180-240

SS-CPG180-240 specifications

Goodman Manufacturing has been recognized for its commitment to producing high-quality heating, ventilation, and air conditioning (HVAC) systems that provide comfort and reliability. Among its lineup, the Goodman SS-CPG180-240 stands out as an exceptional choice for those seeking efficient climate control solutions, particularly in residential and light commercial applications.

The Goodman SS-CPG180-240 is a packaged gas/electric unit designed for superior performance and efficiency. One of its main features is its robust two-stage heating and cooling capability, which ensures optimal temperature regulation while minimizing energy consumption. This model effectively combines a high-efficiency air conditioning system with a powerful gas furnace, delivering the flexibility needed to maintain comfortable indoor conditions throughout the year.

One of the defining characteristics of the Goodman SS-CPG180-240 is its high energy efficiency. With an impressive Energy Efficiency Ratio (EER) and Seasonal Energy Efficiency Ratio (SEER), this system not only provides cost savings through lower energy bills but also meets or exceeds efficiency guidelines. The use of R-410A refrigerant contributes to environmentally friendly performance while helping to ensure reliable operation and enhanced performance.

The installation and maintenance of the Goodman SS-CPG180-240 are also made easier due to its compact design. The unit features a durable, corrosion-resistant cabinet that stands up against harsh weather conditions, ensuring longevity and reliability. Moreover, its access points have been thoughtfully designed to simplify service visits for HVAC technicians, allowing for quicker maintenance and repairs.

Additionally, this packaged unit is equipped with modern technological advancements, including a smart thermostat compatibility feature that allows users to optimize their climate control settings remotely. This feature not only adds convenience but also enables better energy management, as homeowners can monitor and adjust their system from anywhere.

In summary, the Goodman SS-CPG180-240 is a well-engineered packaged system that combines efficient heating and cooling performance with user-friendly features. Its high energy efficiency, compatibility with smart technologies, and ease of maintenance make it an ideal choice for homeowners and light commercial users aiming to achieve optimal indoor comfort and cost savings.