Motorola AP 73 Editing the Phone Access / Deaccess Codes, ➋ Press, To enter the edit mode

Page 57

Special Programming Mode (SPM)

NOTE

A ﬂashing channel number indicates that the chan- nel is unprogrammed (erased).

➌Press Toggle Light / Enter and Parameter Transfer Button (4) to erase a programmed channel (non- ﬂashing channel numbers).

NOTE

A valid keypress tone sounds when the channel has successfully erased. Pressing Toggle Light / Enter and Parameter Transfer Button (4) on an unprogrammed channel results in an invalid key- press tone and the keypress is ignored.

➍To exit this menu, select another menu item by turning the Selector Knob (2).

Editing the Phone Access / Deaccess Codes

➊In SPM, rotate the Selector Knob (2) to the Edit

Phone Access ( ) or Edit Phone Deaccess

( ) menu.

➋Press

OFS

or

MEM

to enter the edit mode.

NOTE

The LCD Screen (18) displays the current access / deaccess code. For a code which exceeds the 6- digit display length, the rightmost digit ﬂashes to indicate that more digits exist on the right.

➌Enter the new access / deaccess code (up to 8 dig- its) using any of the numeric keys, A, B, C, D,* and #.

2-Year Warranty

49

Image 57

Contents Portable Radios Basic Operation AP73 Quick ReferenceMHz Operation Individual Call, , Group Call, or All Call SPM Dis- SPM Browse Menu Year Limited Warranty For Radios Step Copyright Information Contents Coverage of this User Guide IntroductionRadio Antenna Antenna Adaptor Spring Belt Clip Packing InformationKnobs, Buttons, Connectors and Others Low Power / Frequency Step Button Signal ButtonPush-To-Talk PTT Button Squelch / PL ButtonAccessory Connector Mode / Backspace ButtonSpeaker Left Scroll / Offset ButtonBattery Pack Enable / Disable PTT ID KeyBattery Latches Numeric KeypadGetting Started Installing and Removing BatteriesAttaching and Removing the Antenna Attaching and Removing the Belt ClipCharging NiCd Battery Pack Length of time required to fully charge a new battery Charging your Battery for the First timeLength of time required to fully recharge a used battery Charging your Battery Subsequently➊ Make sure the battery pack is attached to the radio Charging with Wall Charger➊ Place the Charger Insert into the Desktop Charger Charging with Desktop Charger➋ Insert the radio / battery into the charging docket High / Low Power Output Adjusting the VolumeBasic Operations Turning the Radio OnTransmitting a Message Receiving a Message Press and hold to enable / disable PTT ID Additional OperationsDisplay Backlight Changing Squelch Modes Locking / Unlocking the Radio’s FunctionCtcss Setting Squelch Level ➊Press and hold Selecting The Receive PL / DPL Squelch Code➋P ress Selecting a Transmit PL / DPL Squelch CodeRPL.xxx PL Freq Equiv TPL.xxx PL Code Receive And Transmit PL / DPL Code TablesEquiv Selecting MHz Mode MHz Mode OperationsSelecting the Frequency Step Size ➊Press and holdEnter the desired frequency Selecting a Receive FrequencyCombination Ii Through The Selector KnobSelecting The TX Offset Programming a User-Deﬁned TX FrequencyTo ﬂash takes about 3 seconds MHz Mode Operations MHz Mode Operations Selecting Memory Mode Memory Mode OperationsSelecting a Memory Channel Rotate the Selector Knob 2 to the desired chan- nel numberProgramming a Memory Channel Loading a Memory Channel Programmable Band Scan Scan OperationsFrequency range ➊PressRotate the Selector Knob 2 anti-clockwise ➋PressPressing Push-To-Talk PTT Button 6, a digit on Transmitting During Band ScanningBefore Memory Channel ScanPress Push-To-Talk PTT Button 6 to talk, release to listen Press DScan Operations Placing a Telephone Call Dtmf Telephone InterconnectPress Stores the preprogrammed telephone numberStoring a Phone Number Last Number RedialPress and hold Push-To-Talk PTT Button Then pressTo scroll the cursor to the left or right If you make a mistake, pressDisplaying a Stored Phone Number Receiving a Voice Selective Call Voice Selective Call OptionalProgrammed see Edit Selective Call IDs on Sending a Voice Selective Call Entering SPM Special Programming Mode SPM Exiting SPM Turn off the radio to exit SPMSPM Browse Menu Editing the Channel Scan List Editing SPM ParametersTo scroll through the channels Erase a Single Channel from MemoryEditing the Phone Access / Deaccess Codes To enter the edit mode➋ Press ➊ In SPM, rotate the Selector Knob 2 to the PTT ID Edit PTT IDIng PTT ID Edit Selective Call IDs Setting the Selective Call Tone Status Editing Time Out Timer➋ Use To change the current statusTo toggle between On and Off Setting the Sidetones StatusSetting the Battery Saver Status Setting the Alert Tone Volume➋ Use OFS Options To scroll through the threeSetting the Accessory Sense Option Setting the Battery Type➊ In SPM, rotate the Selector Knob 2 to the Set To scroll through the optionsFactory Reset Feature Special Programming Mode SPM LCD Segments and Indicators IndicatorsIndicators with Segments Alert Tone Indicators Acknowledgment ID Decode Individual Selective Call DecodeGroup and All Call Selective Call Decode Nuisance Channel DeleteInformation For Safe, Efﬁcient Opera- tion Exposure To Radio Frequency EnergyFor Portable Two-way Radios Potentially Explosive Atmospheres Electromagnetic Interference/compatibilityFor Vehicles With An Air Bag Blasting Caps And AreasUnited States Recycling / Disposal of NiCd BatteriesEurope AsiaJapan Licensing & Service Information ServiceLicensing Troubleshooting NiCd battery does not charge or last long enoughRadio is dead Alkaline Battery does not last long enough 10 minutes Solution Clean battery and charger contacts oftenRadio will not talk to other radios in system Solution Use proper radio etiquetteHearing other conversations or noise on your radio Limited talk rangeYou hear constant static from speaker You have tried a solution for any of the above sympToms, without success Accessories Battery & Charging AccessoriesAntennas Audio & Signalling Accessories for all models Carrying Cases & AccessoriesRadio to Radio Cloning Accessory Limited Warranty Motorola Radio Products Radio Speciﬁcations GeneralReceiver Transmitter