Motorola AP 73 user manual Battery & Charging Accessories, Antennas

Page 81

Accessories

Accessories

NOTE

Please note that all accessories may not be avail- able in all markets. Contact your dealer for more information.

Battery & Charging Accessories:

HTN8232_	110V	- Standard Charging Adapter (Wall)
HTN9002_	220V	- Standard Euro Charging Adapter
	(Wall)
PMLN4097_	Alkaline Battery Case
PMNN4002_	Ni-Cd Rechargeable High Capacity Battery
	Pack
PMNN4003_	Ni-Cd Rechargeable Low Capacity Battery
	Pack
PMTN4020_	110V	- Rapid Desktop Battery Charger /
	Insert
PMTN4021_	110V	- Standard Desktop Battery Charger /
	Insert
PMTN4022_	220V	- Rapid Desktop Battery Charger /
	Insert with Euro Plug
PMTN4023_	220V	- Standard Desktop Battery Charger /
	Insert with Euro Plug

Antennas:

PMAD4012_	VHF 9cm Antenna, 136-155 MHz
PMAD4013_	VHF 9cm Antenna, 155-174 MHz
PMAD4014_	VHF 14cm Antenna, 136-155 MHz
PMAD4015_	VHF 14cm Antenna, 155-174 MHz
PMAE4003_	UHF 9cm Antenna, 430-470 MHz
HLN8262_	External Antenna Adapter (BNC)

2-Year Warranty

73

Image 81

Contents Portable Radios Basic Operation AP73 Quick ReferenceMHz Operation Individual Call, , Group Call, or All Call SPM Dis- SPM Browse Menu Year Limited Warranty For Radios Step Copyright Information Contents Coverage of this User Guide IntroductionRadio Antenna Antenna Adaptor Spring Belt Clip Packing InformationKnobs, Buttons, Connectors and Others Low Power / Frequency Step Button Signal ButtonPush-To-Talk PTT Button Squelch / PL ButtonAccessory Connector Mode / Backspace ButtonSpeaker Left Scroll / Offset ButtonBattery Pack Enable / Disable PTT ID KeyBattery Latches Numeric KeypadGetting Started Installing and Removing BatteriesAttaching and Removing the Antenna Attaching and Removing the Belt ClipCharging NiCd Battery Pack Length of time required to fully charge a new battery Charging your Battery for the First timeLength of time required to fully recharge a used battery Charging your Battery Subsequently➊ Make sure the battery pack is attached to the radio Charging with Wall Charger➊ Place the Charger Insert into the Desktop Charger Charging with Desktop Charger➋ Insert the radio / battery into the charging docket High / Low Power Output Adjusting the VolumeBasic Operations Turning the Radio OnTransmitting a Message Receiving a Message Press and hold to enable / disable PTT ID Additional OperationsDisplay Backlight Changing Squelch Modes Locking / Unlocking the Radio’s FunctionCtcss Setting Squelch Level ➊Press and hold Selecting The Receive PL / DPL Squelch Code➋P ress Selecting a Transmit PL / DPL Squelch CodeRPL.xxx PL Freq Equiv TPL.xxx PL Code Receive And Transmit PL / DPL Code TablesEquiv Selecting MHz Mode MHz Mode OperationsSelecting the Frequency Step Size ➊Press and holdEnter the desired frequency Selecting a Receive FrequencyCombination Ii Through The Selector KnobSelecting The TX Offset Programming a User-Deﬁned TX FrequencyTo ﬂash takes about 3 seconds MHz Mode Operations MHz Mode Operations Selecting Memory Mode Memory Mode OperationsSelecting a Memory Channel Rotate the Selector Knob 2 to the desired chan- nel numberProgramming a Memory Channel Loading a Memory Channel Programmable Band Scan Scan OperationsFrequency range ➊PressRotate the Selector Knob 2 anti-clockwise ➋PressPressing Push-To-Talk PTT Button 6, a digit on Transmitting During Band ScanningBefore Memory Channel ScanPress Push-To-Talk PTT Button 6 to talk, release to listen Press DScan Operations Placing a Telephone Call Dtmf Telephone InterconnectPress Stores the preprogrammed telephone numberStoring a Phone Number Last Number RedialPress and hold Push-To-Talk PTT Button Then pressTo scroll the cursor to the left or right If you make a mistake, pressDisplaying a Stored Phone Number Receiving a Voice Selective Call Voice Selective Call OptionalProgrammed see Edit Selective Call IDs on Sending a Voice Selective CallEntering SPM Special Programming Mode SPMExiting SPM Turn off the radio to exit SPMSPM Browse Menu Editing the Channel Scan List Editing SPM ParametersTo scroll through the channels Erase a Single Channel from MemoryEditing the Phone Access / Deaccess Codes To enter the edit mode➋ Press ➊ In SPM, rotate the Selector Knob 2 to the PTT ID Edit PTT IDIng PTT ID Edit Selective Call IDs Setting the Selective Call Tone Status Editing Time Out Timer➋ Use To change the current statusTo toggle between On and Off Setting the Sidetones StatusSetting the Battery Saver Status Setting the Alert Tone Volume➋ Use OFS Options To scroll through the threeSetting the Accessory Sense Option Setting the Battery Type➊ In SPM, rotate the Selector Knob 2 to the Set To scroll through the optionsFactory Reset Feature Special Programming Mode SPM LCD Segments and Indicators IndicatorsIndicators with Segments Alert Tone Indicators Acknowledgment ID Decode Individual Selective Call DecodeGroup and All Call Selective Call Decode Nuisance Channel DeleteInformation For Safe, Efﬁcient Opera- tion Exposure To Radio Frequency EnergyFor Portable Two-way Radios Potentially Explosive Atmospheres Electromagnetic Interference/compatibilityFor Vehicles With An Air Bag Blasting Caps And AreasUnited States Recycling / Disposal of NiCd BatteriesEurope AsiaJapan Licensing & Service Information ServiceLicensing Troubleshooting NiCd battery does not charge or last long enoughRadio is dead Alkaline Battery does not last long enough 10 minutes Solution Clean battery and charger contacts often Radio will not talk to other radios in system Solution Use proper radio etiquette Hearing other conversations or noise on your radio Limited talk rangeYou hear constant static from speaker You have tried a solution for any of the above sympToms, without success Accessories Battery & Charging AccessoriesAntennas Audio & Signalling Accessories for all models Carrying Cases & AccessoriesRadio to Radio Cloning Accessory Limited Warranty Motorola Radio Products Radio Speciﬁcations GeneralReceiver Transmitter