Jensen JCR-300 Listening to Radio, Using the Line in to Listen to External Audio Player

Page 12

-When sleep sound is playing, its volume can be adjusted from low to high (level 1-4) by pressing the > (UP) (#6) or < (DOWN) (#4) BUTTONS. The selected sleep sound volume will be displayed.

-To change the sleep sound during sleep, press the SNOOZE BAR (#11) and use “Play Sleep Sound” voice command to change it as usual. Say “Cancel” when asked to choose the sleep time to keep the current sleep time.

LISTENING TO RADIO

1.Select your desired radio band using the BAND SELECTOR (#7) for AM or FM.

2.Press the ON/OFF BUTTON (#12) to turn radio on.

3.Rotate the TUNING CONTROL (#9) to your desired radio station according to the dial scale on the unit.

4.Rotate the VOLUME CONTROL (#1) to adjust to the desired output level.

5.To turn off the radio, press the ON/OFF BUTTON (#12).

TIPS FOR BEST RECEPTION

AM – The AM antenna is located inside the cabinet of the unit. If AM reception is weak, change the position of unit until the internal antenna picks up the strongest signal.

FM – During FM reception, always keep the FM WIRE ANTENNA (#21) fully extended for best performance. However, if FM reception is weak, try repositioning the unit until you get the best reception.

USING THE LINE IN TO LISTEN TO EXTERNAL AUDIO PLAYER

You may playback your favorite music from your iPod or a portable digital audio player using the Line in function.

1.Connect the headphone jack of your external device to the LINE IN JACK (#18) at the rear cabinet of this unit using a stereo cord with a 3.5mm phone plug on either ends. (Note: the stereo cord is not included)

2.Press the ON/OFF BUTTON (#12) to turn on the radio. It will automatically switch to Line In mode when a suitable stereo cord is correctly connected.

3.Start playing your external audio device.

4.Slowly increase the volume control of the unit until the desired level is obtained. To avoid output sound distortion due to overloading, you may need to lower the volume output of your audio device.

Note: the stereo music from your audio device will be converted to a monaural audio output.

5.Turn off your external audio device first when you finish listening.

6.Then unplug the stereo cord from the LINE IN JACK (#18) and normal radio reception will resume. Note: If the unit is set for wake to radio but with an external player connected to the LINE IN JACK, it will revert

to the beep alarm sound instead.

DIMMER CONTROL

MANUAL SETTING

The display HI/LO DIMMER BUTTON (#19) is located on the back of the unit. Pressing it will toggle between bright and dim backlight options for the display.

USING TALK ’N SET

1.Start by saying the trigger word “Hello Clock Radio” or press the Snooze Bar (#11).

2.The unit will reply “Yes” and will wait for your next command.

3.Say “Display” and the unit will reply “Say Display Low or Display High”.

4.Say “High” or “Low” to set the display brightness accordingly. You can also say the command “Cancel” and the display will stay at it’s current setting.

5.If you do not say the command word correctly, the unit will prompt you to repeat or start all over again.

RESETTING THE UNIT

After you have installed backup batteries and connected the unit to AC power source for the first time, we recommend you to press the RESET Button (#15) at the bottom of the cabinet to correctly initialize it.

In case of an erroneous display or prolonged abnormal behavior during normal use, you can also safely restore it to its factory preset conditions by pressing the RESET Button (#15). Please note that all personal settings including current time, alarm time and sleep session will be cleared. So, be sure to set up the clock again according to previous sections above.

E-11

Image 12
Contents Page Important Safety Instructions Save this Instructions Compliance with FCC RegulationsDear Jensen Customer Controls and Functions of Unit Location of ControlsPower Requirements Replacing Backup BatteriesConnecting the Unit to AC Power Source Important NotesSetting UP Daily Alarms and Clock Using Manual SettingsUsing Talk ’N SET Current Time Setting and Reporting Alarm Time and Alarm Sound Setting / CheckingTo SET the Alarm Time AL1/AL2 To SET the Current TimeTo SET the Alarm Wake Sounds AL1/AL2 To Check the Alarm Time AL1/AL2Unit will now ask Would you like to turn off the Alarm? Turning OFF the AlarmSnooze Function Manual OperationSetting UP the Sleep Sound and Time Manual Setting Setting the Sleep SoundActivate Sleep Mode and Setting Sleep Time Using the Line in to Listen to External Audio Player Resetting the UnitListening to Radio Dimmer ControlSpecifications Care and MaintenanceTroubleshooting Guide Symptom Possible Cause SolutionDAY Limited Warranty and Service Valid in the U.S.A only