MANUAL SETTINGS
It is necessary to set the desired US TIME ZONE.
TIME ZONE
• Press MODE button once so that the Day of the Week abbreviation is displayed to the right of the time; for example: pm 2:37tu
• Select the Time Zone by pressing and holding UP (
) button for 3 seconds
• Keep holding UP (
) button until the desired US Time Zone (Pacific, Mountain, Central or Eastern) is highlighted on the display’s US map, located to the right of the time display and above the day of the week
• Release the UP (
) button. The Time Zone is set
CLOCK
• Press and hold MODE button for 3 seconds: the year will flash. Press UP (
) or DOWN ( ) to change flashing digits.
• After the year is set, press MODE button to confirm and move to the next parameter (month)
• Continue setting month, date, hour, minutes, language for the day of the week and temperature in Fahrenheit or Celsius
• Press MODE for the last time to return to the time of day with seconds, after the last parameter is set
CLOCK ALARMS
The
• If Weekday (W) alarm is activated, it will sound at the set time and the alarm icon will flash Mondays through Fridays
• If Single (S) day alarm is activated, it will sound at the set time and the alarm icon will flash only for this specific day and will not activate on subsequent days
• If Ice Warning Alarm
NOTE: Ice Warning Alarm can be set only if one or both - Weekday or Single alarm - are programmed.
17
SETTING THE WEEKDAY (W) AND SINGLE DAY (S) | |
ALARMS | |
• | Press ALARM button once to enter into the alarms setting |
| mode. The default alarm is a Weekday alarm (W). The |
| abbreviation “OFF” with a letter “W” next to it will be |
• | displayed, if the alarm has not been set previously |
Press and hold ALARM button for two seconds. The hour | |
• | digit will flash |
Adjust the hour using UP ( ) or DOWN ( ) buttons | |
• | Press ALARM button again. The minute digits will flash |
• | Adjust the minutes using UP ( ) or DOWN ( ) buttons |
• | Press ALARM button again to confirm and the weekday |
• | alarm time will be set |
Set Single (S) day alarm if desired in the same manner | |
SETTING THE ICE WARNING ALARM
• Press ALARM button once to enter into the Ice Warning Alarm setting mode. The abbreviation OFF with a
• Press and hold ALARM button for two seconds. The number 30 will flash, meaning that if selected, the alarm will sound 30 minutes earlier than the Weekday or Single alarm.
• | Select the desired Ice Warning Alarm interval in 15 minutes |
| increments between 15 and 90 minutes, using UP ( ) or |
• | DOWN ( )buttons |
Press ALARM button to confirm and exit from the alarm | |
| setting mode. |
ACTIVATING THE ALARM
•Press ALARM button to enter into the desired alarm mode.UP (
) to activate or DOWN ( ) to deactivate• Press
desired alarm. When alarms are activated, the corresponding icons W, S or
18
SNOOZE
When the time alarm sounds, press the SNOOZE/LIGHT button to temporarily stop it. After the SNOOZE/LIGHT is depressed, the time alarm sound will resume in four minutes. If the alarm is not disabled after that, it will sound for two more minutes and then will stop by itself.
BACKLIGHT
The backlight feature is enabled only after the time is set. To activate the backlight press the SNOOZE/LIGHT button once, and both – clock and weather station displays - will light up for five seconds.
PRECAUTIONS
This product is engineered to give you years of satisfactory service if handled carefully. Here are a few precautions:
•Do not immerse the units in water.
•Do not clean the units with abrasive or corrosive materials. They may scratch the plastic parts and corrode the electronic circuits.
•Do not subject the product to excessive force, shock, dust, temperature, or humidity, which may result in malfunctions, shorter lifespan, damaged batteries, and damaged parts.
•Do not tamper with the units internal components. Doing so will invalidate the warranty and may cause damage. These units contain no
•Use only fresh batteries. Do not mix new and old batteries.
•Read the user's manual thoroughly before operating the units.
TROUBLESHOOTING
Check here before contacting customer service.
Issue | Symptom | Solution |
Main unit | US Atomic Time | Place unit by the |
| signal is not received | window and keep it |
|
| there overnight |
Remote sensor | Cannot locate remote | Check batteries |
| sensor | Check location |
|
| Press and hold DOWN |
|
| ( ) button on the main |
|
| unit to search for the |
|
| signal form the remote |
|
| sensor |
| Cannot change the | Press "RESET" after |
| channel | setting the channel |
| Cannot change the ºC | Press "RESET" after |
| to ºF and back | setting ºC/ºF |
| Data does not match | Initiate manual sensor |
| data on the main unit | search (Press and hold |
|
| DOWN ( ) button on |
|
| the main unit) |
19
20