Philips AJL700/37B quick start Mount it, Use it

	Mount it
3
	Ask a friend to help out. An extra hand to hold the unit makes mounting easier and
	quicker.
	A	Template

A

•Cut the template to fit inside the cabinet.

• Align the template border marked "FRONT" along the front edge of your cabinet.

• Use adhesive tape to fix the template.

• Drill 1/4 inch holes, as marked X on the template.

•Remove the template when you finish drilling.

Tip

–Clean the bottom of the cabinet surface and also empty your cabinet before mounting.

–Place the unit in a clean, safe place when drilling to avoid wood shavings dropping into the ventilation slots.

–Use a nail to start each drill hole.

–Drill from the bottom upwards if you do not have enough room inside the cabinet.

–Hold your drill firmly at 90o with the cabinet bottom and drill holes at low speed.

–Clear wood shavings.

C

•Manually fasten the 4 long screws down into the spacer holder holes to mount your set. Start screwing at opposite corners of the unit for better support.

C

Tip

To prevent damage to your

set, do not use an electric drill to secure screws when mounting!

–If the overhang is more than 1 1/4 inch, use longer screws (not included).

B

Using the spacers

On the spacers, there are 4 pairs of notch length	B
options. Depending on the thickness of you cabinet bot-	Spacer
tom (with/ without an overhang), these notch lengths
correspond to the 4 notch height in the space holders,
and allow you to adjust to the best height to help you
mount the unit.

• Measure the height of the cabinet bottom and/over- hang.

• Turn the spacer counterclockwise to determine which of the 4 heights is most suitable: Low • • High. Align to the arrow indication.

• Insert the spacers accordingly.

L (Low)

L••H (4 heights)

Arrow

H L

D

Using the adapter bracket

Find a suitable place to mount the adaptor bracket.

1Use 2 small screws (supplied) to mount the bracket.

2Insert the adapter into the bracket as shown.

3Use the adapter bracket to wrap and secure the power cord so that excess cord does not hang down.

4

1

2 3

4	Use it
	For full details, please read and follow the instructions inside the User manual.

A

Power supply

• Connect the power plug to the wall outlet.

• Press POWER (or STANDBY.ON) to switch on.

D

How to watch TV on the unit

1Press TV once or more to select TV or CATV mode .

2In CATV, press ENTER on the remote control selects HRC, IRC, STD or AUTO mode.

3The first time you use the TV, press and hold AUTO PROG /RADIO PROG on the set until the channel

number starts running.

•Available channels are programmed.

4Use the Numeric Keypad (0-9)on the remote con- trol to select the channel number directly.

DISC

AV

SHUFFLE

ERASE/WRITE PROG

B

POWER

Using the TV screen

1Press PUSH at the bottom the set to release the TV panel. .

2Pull down the panel (maximum 115º).

3Turn around the panel to find the screen.

4Adjust the screen to a suitable angle (maximum 270º).

Tip

–Swivel with care to avoid breakage. Screen rotates a maximum 2700 only.

C

How to play a DVD /CD

•Select DVD source.

•Insert a DVD/CD.

•Press PLAY/PAUSE to start disc playback.

Insert a12cm disc

115 maximum

PUSH

DISC

AV

SHUFFLE

ERASE/WRITE PROG

270 maximum

E

Improve radio reception

Position the antenna as far as possible from a TV,VCR or radiation source.

FM:

Keep the FM antenna as horizontal as possible . Fix the antenna’s end to the wall.

AM:

Position vertically. If necessary, use 2 small screws (supplied) to fix the antenna to a flat, hard and stable place.

AM

CLOCKSET PICTURE