Bard WG-Series Understanding HOW Your Furnace Works, Alteration of Furnace Controls

Page 5

2.3 ALTERATION OF FURNACE CONTROLS

WARNING

Do not alter any gas or electrical controls (gas control or safety controls) in any manner. Altering them could cause furnace to operate unsafely resulting in damage, injury or death.

The ignition system consists of a direct spark igniter (DSI) and remote sensor. When the thermostat calls for heat the DSI sparks to light main burner gas.

Once ignited the remote sensor confirms flame carryover to all burners.

There is a 60 second delay after main burner is on until the comfort air blower starts on heating speed. After the thermostat is satisfied, the burners will go off as gas valve closes. The inducer will continue to run for 30 seconds, and the comfort air blower will continue to run for 2-1/2 minutes.

SECTION 3 • UNDERSTANDING HOW YOUR FURNACE WORKS

Your installer should have given you a detailed explanation of how the furnace operates. Shown below are the basic operation characteristics and sequence of operation. If you have any questions consult your installer and/or service agency.

* * IMPORTANT * *

There are many types of thermostats compatible with this furnace. Make sure you understand the specific type installed. Ask installer for detailed explanation, and retain thermostat instruction manual for reference.

This furnace is equipped with a vent shut-off system which monitors the combustion air into the burners by means of a pressure sensing device. When the vent becomes blocked, this device turns off the gas valve circuit to prevent flue products from entering the structure. In the event that this occurs, shut off furnace and contact a qualified service agency.

3.1 BASIC OPERATION – HEATING CYCLE

This furnace is operated by an Integrated Furnace Control (IFC) and a gas control system which controls all functions of the furnace.

On a call for heat from the thermostat, the IFC first turns on the inducer motor. The pressure switch then closes signaling the ignition control to proceed with ignition function.

3.2 BASIC OPERATION – COOLING CYCLE

On a call for cool the compressor and condenser fan will start immediately, and the comfort air blower will start 7 seconds later on cooling speed. Note: Some models may be equipped with optional Low Ambient Control that will cycle the condenser fan motor to maintain proper refrigerant pressures under lower outdoor temperature conditions. When the thermostat is satisfied the compressor and condenser fan will stop and the comfort air blower will continue to operate for 60 seconds.

3.2.1COMPRESSOR CONTROL MODULE (CCM)

All models are equipped with a compressor control module. This control is an anti-short cycle/lockout timer with high and low pressure switch monitoring and alarm relay output.

Delay on Make Timer and Break Time Delay

•On initial power up, or any time the power is interrupted to the unit, the delay on make period begins. This delay will be 2 minutes plus 10% of the delay on break setting. This feature assures that pressures will be equalized for normal start up if there are brief power interruptions, and can accommodate staggered starts for dual unit installations as long as the off delay periods are set differently for the two units.

•During routine operation of the unit with no power interruptions the compressor will operate on demand with no delay as long as off delay time has been met.

•Adjustable 30 second to 5 minute delay on break timer assures that pressures can equalize if units are short cycled by the operating controls or personnel. Recommended settings would be 2 minutes for unit 1 and 3 minutes for Unit 2.

Manual 2100-366 Page 3

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Bard Manufacturing Company What to do if YOU Smell GASContents Signal Words Important Safety PrecautionsRating Plate Information GAS and Combustion ProductsManual 2100-366 Alteration of Furnace Controls Understanding HOW Your Furnace WorksBasic Operation Heating Cycle Basic Operation Cooling CycleManual FAN Continuous Airflow Operation Phase MonitorTurning OFF Furnace in AN Emergency Electrical SHUT-OFF Devices GAS and Electrical SHUT-OFF Devices GAS SHUT-OFF DevicesTypical GAS Piping Action Possible Emergencies Recommended ActionsOperating Your Furnace Proper Maintenance of Your FurnaceLubrication Requirements Make Sure AIR Filters is in PlaceStart UP Procedure Have Your Furnace Checked Annually Keep AIR Filters CleanDo not Obstruct Duct Work Periodic Inspections Filter LocationsVentilation Option Assemblies START-UP Procedures DecalOutdoor Coil Replacement Parts

WG-Series specifications

The Bard WG-Series is a notable range of water-source heat pump units, designed to provide efficient heating and cooling solutions tailored to residential and commercial applications. This series stands out for its compact design, energy efficiency, and innovative features that cater to modern demands for sustainability and reliability.

One of the primary characteristics of the Bard WG-Series is its use of advanced heat pump technology. These units harness the energy from water sources, whether it be ponds, lakes, or groundwater, which allows them to operate efficiently year-round. This sustainable approach reduces reliance on traditional fossil fuels, making it a favored choice for environmentally conscious users seeking to lower their carbon footprint.

Key features of the Bard WG-Series include its high-efficiency scroll compressors which enhance the unit's performance by optimizing energy consumption. This technology not only supports efficient heating and cooling cycles but also contributes to quieter operation compared to conventional systems, ensuring comfort within the living or working environment.

Another important aspect of the Bard WG-Series is its ability to provide both heating and cooling in one compact unit. This dual functionality minimizes the need for separate systems, streamlining installation and maintenance processes while also reducing overall system costs. The units are designed with user-friendly interfaces that allow for easy monitoring and management of system performance.

The build quality of the Bard WG-Series is commendable, featuring durable, corrosion-resistant materials that ensure longevity and reliability in various environmental conditions. Enhanced insulation within the units helps maintain temperature consistency, further increasing energy efficiency and comfort levels.

Additionally, Bard has incorporated advanced controls and automation features in the WG-Series that allow users to remotely manage their heating and cooling needs. Integration with smart home systems is possible, providing users with greater convenience and control over their HVAC systems.

Overall, the Bard WG-Series represents a significant advancement in heat pump technology, marrying efficiency with sustainability. Its innovative features cater to contemporary energy demands, making it an excellent choice for those seeking reliable, eco-friendly building solutions. With its combination of performance, user-friendliness, and durability, the Bard WG-Series is poised to meet the heating and cooling needs of a diverse range of applications.
Top Page Image Contents