Modos de Operación, Technical Support | Campbell Hausfeld NS219000

Las ranuras

Manual de Instrucciones

Models NS219000, NS289100, NS289500 & NS349000

5.Cambie la argolla

retenedo- ra en la punta no des-

gastable,

luego almacene la punta en un lugar seguro para utilizarla más adelante.

CÓMO INSTALAR LA PUNTA NO DESGASTABLE

1. Desconecte el abastecimiento de aire de la clavadora.

2.Retire todos los sujetadores del cargador (ver CÓMO DESCARGAR LA CLAVADORA).

3.Retire la argolla que

sujeta a la punta no des- gastable.

Modos de Operación

! ADVERTENCIA Siemprecerciórese de saber en que modo va a operar la clavadora antes de comenzar a usarla. De lo contrario, le podría ocasionar la muerte o heridas graves.

CICLO SENCILLO
Este método se
recomienda para
la colocación
exacta del clavo.	2
1	2
Le debe instalar a

la clavadora el pasador para ciclo sencillo. Este sistema requiere que oprima el gatillo cada vez que vaya a clavar un clavo. Para clavar el elemento de contacto debe tocar la superficie de trabajo y el operador debe oprimir el gatillo. Igualmente, puede oprimir el gatillo primero y después hacer el contacto.

Debe soltar el gatillo antes de clavar otro clavo.

ELEMENTO DE CONTACTO

Chequée

5. Presione el

Elemento de Contacto de

Trabajo contra la superficie de trabajo sin

apretar el gatillo. La clavadora NO DEBE OPERAR. No use la herramienta si opera sin apretar el gatillo. Se pueden producir lesiones personales.

6. Remueva la clavadora de la superficie de

trabajo. El Elemento de Contacto de Trabajo tiene que

volver a su posición original. La clavadora NO DEBE OPERAR. No use la herramienta si opera mientras está levantada de la superficie de trabajo.

7. Apriete el gatillo y presione el

Elemento de

4. Squeeze the pusher and latch together to

unlatch the

pusher once all nails have

been removed.

ADJUSTING THE NAIL PENETRATION

The NS219000, NS289100, NS289500, and NS349000 nailers are equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface.

1.	Adjust the operating pressure to a
	pressure which will consistently
	drive the fasteners. Do not exceed
	the maximum operating pressure of
	the nailer of 120 psi.
2.	To adjust the depth-of-drive, loosen
	the 4mm bolt on the top of nose. To
	increase depth, push WCE in toward

ADJUSTING THE DIRECTION OF THE EXHAUST

	The NS219000,
	NS289100,
	NS289500, and
	NS349000	Rotate
	nailers are	Rotate
	nailers are

equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Using the 5mm wrench provided, loosen the deflector screw; then twist the deflector to any direction desired and re-tighten the screw.

CLEARING A JAM FROM THE NAILER

1. Disconnect nailer from air supply.

2. Remove all nails

from the

Technical Support

Please call our Nailer Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this nailer or for additional copies of this manual.

If calling from Ohio or outside of the continental United States, please call 1-513-367-1182.

Fastener And Replacement Parts

Use only

!WARNING genuine Campbell Hausfeld fasteners (or equivalent - see Fastener Interchange Information). Use only genuine Campbell Hausfeld replacement parts. Never substitute parts. Do not use modified parts or parts which will not give equivalent performance to the original equipment. Tool performance, safety and durability could be reduced. When ordering replacement parts or fasteners, specify by part number.

Nailer Repair

4. Coloque

cuidadosa-

! PRECAUCION el

Contacto de

nose as much as desired. Re-tighten

magazine (see

Nailer repairs must be performed by

mente la

punta no des- gastable sobre

el extremo del

elemento de contacto de trabajo (WCE). Coloque la

punta no

desgastable sobre el elemento de contacto de trabajo (WCE) haciendo que algunas ranuras dentadas en cada pieza estén alineadas y se ajusten con precisión.

5. Coloque la argolla

retenedora sobre la

punta no des- gastable, y presione firmemente.

6.Verifique que el elemento de contacto

de trabajo

funcionamiento del mecanismo del elemento de contacto antes de cada uso.

El elemento de contacto se debe desplazar libremente, sin pegarse, a lo largo del área de desplazamiento. El resorte del elemento de contacto debe regresar el elemento de contacto a su posición original totalmente extendido. No use la clavadora si el mecanismo del elemento de contacto no está funcionando adecudamente. Podría ocasionarle heridas.

1.Desconecte la clavadora de la

fuente de suministro de aire.

2.Saque todos los clavos del

cargador (Vea la Sección Carga- Descarga).

3.Cerciórese de que el gatillo y el

elemento de

Trabajo contra la superficie de trabajo. La clavadora NO DEBE OPERAR.

8. Presione el
Elemento de
Contacto de
Trabajo	1	2
contra la

superficie de trabajo. Apriete el gatillo. La clavadora DEBE OPERAR.

CÓMO CARGAR LA CLAVADORA

1.Siempre conecte la herramienta al abastecimiento de aire antes de cargar los sujetadores.

2. Jale el	El mecanismo	El
mecanismo	El mecanismo	El
mecanismo	del	enganche
del	empujador
empujador	empujador
empujador	de clavos
de clavos	de clavos
de clavos
hasta que
éste
engrane
con el
enganche
del cargador.

bolt. To decrease depth, pull WCE

out as much as desired. Re-tighten

bolt.

3. Make sure that the trigger and work

contact element (WCE) move freely

up and down without binding or

sticking after each adjustment.

ANTI-DRY FIRE

The NS219000 is equipped with an Anti-Dry Fire feature. This prevents the WCE from being pushed in when only a few nails remain. Simply load new nail clip behind remaining nails to continue shooting.

Loading/

Unloading).

Failure to do so will cause the nails to eject from the front of the tool.

3. Insert a

screw- driver into the

nose of the tool. Push up

on the driver blade to free the jammed nail.

4.Grab the jammed

nail with pliers and remove.

qualified and experienced service people ONLY.

Assembly Procedure For Seals

When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil, or equivalent, must be added through the air line before testing.

(WCE) y el gatillo se

contacto se muevan

Movimiento

3.Cargue la tira de

muevan fácilmente

hacia arriba y hacia abajo sin pegarse o atracarse.

libremente en ambos sentidos sin atascarse o pegarse.

4. Reconecte la clavadora a la fuente de suministro de aire.

sujetadores en la ranura del cargador.

Asegúrese de que los

clavos estén

colocados en la herramienta en la orientación correcta.

www.chpower.com

4-Sp

NS289500, NS219000, NS349000, NS289100 specifications

Campbell Hausfeld has established itself as a reputable brand in the world of air compressors and pneumatic tools, and their models NS349000, NS219000, NS289100, and NS289500 are prime examples of their commitment to quality and innovation. Each of these air compressors is designed with key features and technologies that cater to various needs in both professional and DIY settings.

The Campbell Hausfeld NS349000 is a robust oil-lubricated air compressor, making it ideal for users seeking durability and longevity. Its large tank capacity allows for extended operation without frequent refills, making it suitable for heavy-duty tasks. The powerful motor ensures high performance and reliability, while the low noise level makes it a great option for indoor use. Additionally, the model features a quick connect air coupler, which enhances convenience by allowing users to change tools effortlessly.

Moving on to the NS219000 model, this air compressor is designed with portability in mind. Weighing less than a typical compressor, it is easy to transport, making it perfect for contractors and homeowners alike. This model features a direct drive design, minimizing maintenance and increasing efficiency. With a maximum pressure of 125 PSI, it provides enough power for various inflation and nailing tasks, ensuring users can tackle a range of projects with ease.

The NS289100 model stands out due to its user-friendly design and versatility. This compressor includes an oil-free pump, which simplifies maintenance and makes it easy to store since there’s no need to worry about oil spills. The NS289100 offers a lightweight design, making it highly portable for on-the-go jobs. Its dual pressure gauges provide easy monitoring of output pressure, ensuring users can keep track of their air supply effectively.

Lastly, the NS289500 model is another oil-free compressor that combines power and quiet operation. It also features a compact design which allows users to store it easily without sacrificing performance. The quick-connect feature further enhances efficiency, enabling users to switch between tasks seamlessly. This model caters to professionals and hobbyists who require a reliable and powerful air compressor without the cumbersome weight.

In summary, all four Campbell Hausfeld air compressor models — NS349000, NS219000, NS289100, and NS289500 — possess features and technologies geared toward efficiency, portability, and low maintenance. Whether you need heavy-duty performance, user-friendly operation, or a lightweight design, these compressors provide versatile solutions for numerous applications, establishing Campbell Hausfeld as a leader in the market.