Friedrich racservmn service manual Problem Possible Cause To Correct

Page 41

PROBLEM

POSSIBLE CAUSE

TO CORRECT

 

 

 

 

 

 

 

Outdoor thermostat does not cut off

Defective thermostat - replace.

Unit does not heat

compressor at the preselected tem-

 

adequately.

perature and bring on heating element.

 

 

Fresh air or exhaust door open.

Check if operating properly. Instruct customer

 

 

on proper use of control.

 

Dirty filter.

Clean as recommended in Owner’s Manual.

 

Unit undersized.

Check heat rise across coil. Refer to perfor-

 

 

mance data sheet on heat rise at various

 

 

outdoor ambients. If heat rise is satisfactory,

 

 

check if insulation can be added to attic or

 

 

walls.

PROBLEM

 

POSSIBLE CAUSE

 

TO CORRECT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Incorrect wiring.

 

Refer to applicable wiring diagram.

 

 

 

Defective solenoid coil.

 

Check for continuity of coil.

 

Unit cools when

 

Reversing valve fails to shift.

 

Block condenser coil and switch unit to cooling.

 

 

 

 

Allow pressure to build up in system, then

 

heat is called for.

 

 

 

 

 

 

 

switch to heating. If valve fails to shift, replace

 

 

 

 

 

 

 

 

 

 

valve.

 

 

 

Inoperative system switch.

 

Check for continuity of system switch.

 

 

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

 

POSSIBLE CAUSE

TO CORRECT

 

 

 

 

 

 

 

Outdoor thermostat does not cut off

Defective thermostat — replace.

 

 

compressor at the preselected tempera-

 

 

 

 

Unit does not heat

ture and bring on the heating element.

 

 

 

 

 

 

 

 

 

 

adequately.

 

 

 

 

 

 

Fresh air or exhaust door open.

Check if operating properly. Instruct customer on

 

 

 

 

 

 

proper use of control.

 

 

Dirty filter.

Clean as recommended in Owner’s Manual

 

 

Unit undersized.

Check heat rise across coil. Refer to performance

 

 

 

 

data sheet on heat rise at various outdoor ambients. If

 

 

 

 

heat rise is satisfactory, check if insulation can be

 

 

 

 

added to attic or walls.

 

 

 

 

 

 

 

 

 

 

 

PROBLEM

 

POSSIBLE CAUSE

TO CORRECT

 

Unit cools when heat is called for.

Incorrect wiring. Defective solenoid coil. Reversing valve fails to shift.

Inoperative system switch.

Refer to applicable wiring diagram. Check for continuity of coil.

Block condenser coil and switch unit to cooling. Allow pressure to build up in the system, then switch to heating. If valve fails to shift, replace valve.

Check for continuity of system switch.

PROBLEM

POSSIBLE CAUSE

TO CORRECT

 

 

 

 

 

Heating capillary tube partially

Check for partially starved outer coil. Replace heating

 

restricted.

capillary tube.

Cooling is ad-

Check valve leaking internally.

Switch unit several times from heating to cooling.

 

Check temperature rise across the coil. Refer to

equate, but heating

 

 

specification sheet for correct temperature rise.

is insufficient.

 

Reversing valve failing to shift

Deenergize solenoid coil, raise head pressure, ener-

 

 

completely — bypassing hot gas.

gize solenoid to break loose. If valve fails to make

 

 

complete shift, replace valve.

41

Image 41
Contents 2003 Table of Contents 00001 1st Digit FunctionRAC Serial Number Identification Guide Page Data Evaporator AIR Operating Electrical Breaker Pressures Ratings Refrig Fuse Performance Evaporator AIR Operating Electrical Breaker Data SS10J10AR-A TEMP. DEG. F Pressures Ratings SC06H10E HeatingAmps WY09A33F-A WY12A33F-A HeatingBtuh Refrigeration System Sequence of Operation Fuse/Circuit Wire SizeBreaker GroundingChecking Compressor Efficiency Thermal Overload ExternalWinding Test Terminal Overload Internal Terminal Overload TestChecking the Internal Overload FAN MotorResistor EQ Model Only See Figure System Control Panel KQ Models Only- See FigureSystem Control Panel System Control Panel YQ Model Only System Control Switch Test System Control Switch WE & WY Models See FigureSystem Control Panel See Figure System Control Switch KS, SS, KM, SM, SL Models See FigureHeat Pump & Electric Heat Models See Figure System Control SwitchTo Adjust Temperature To SET Mode of OperationTo Adjust FAN Speed Smart Center Electronic Control CenterTesting the Electronic Control To SET the TimerTesting the Electronic Control Error Code Listings To SET Hour ClockThermostat SQ & KQ Models See Figure TestThermostat YQ Model Only See Figure Thermostat Models ES, YS, EM, YM, EL, YL See FigureThermostat Bulb Location Thermostat AdjustmentDefrost Thermostat Heat Pump Models Only Capacitor Test Defrost Bulb Location Heat Pump Models OnlyCAPACITOR, RUN See Figure Heat Pumps Reversing Valve See Figure Check Valve OperationTo Test Testing Reversing ValveSolenoid Coil Heat Pump Models Only See Figure Heating Element See Figure VALVE, Drain PAN See FigureSealed Refrigeration System Repairs Equipment RequiredSpecial Procedure in the Case Compressor Motor Burnout Hermetic Component ReplacementRotary Compressor Special Troubleshooting and Service Equipment Must be CapableMethod of Charging Undercharged Refrigerant SystemsOvercharged Refrigerant Systems Restricted Refrigerant System Routine Maintenance Troubleshooting Touch Test Chart To Service Reversing Valves Problem To Correct Troubleshooting CoolingProblem Possible Cause To Correct Cycles Problem Possible Cause To Correct Troubleshooting Heating Heat pumps Problem Possible Cause To Correct Off and the electric element is energized Troubleshooting Heating Cooling/Electric Models Troubleshooting Chart Cooling YES System Cools When Heating is DesiredModels SQ06J10B-B, SQ06J10B-A, SQ08J10C-A, SQ08J10D-A Models KQ08J10B-1, KQ08J10B-A, KQ08J10C-A Schematic YQ06J10B-A ModelModel SC06H10D 619-405-06 Alternate SL28J30B-A, SL35J30-A, SL35J30-BConductor Or Brown RED Blue To Capacitor Bracket Wiring Diagram YS12J33-A, YM18J34B-A, YL24J35C-A Model EQ08J11-A, EQ08J11-B IDT Ovld Neutral WE09A33E-B, WE12A33E-A, WE15A33-A WY09A33F-A, WY12A33G-A Checking Room Temperature Testing The Electronic Control XQ Boards & QME BoardsFriedrich AIR Conditioning CO

racservmn specifications

Friedrich Racervmn is an innovative name in the realm of precision engineering, making significant strides in the development of advanced technologies for various industries. This company stands out due to its commitment to creating high-quality, reliable, and efficient products that cater to the diverse needs of its clientele.

One of the main features of Friedrich Racervmn is its focus on research and development. The company invests heavily in R&D to push the boundaries of what is technically possible. This dedication results in the continuous improvement of their product line and the introduction of cutting-edge solutions that leverage the latest advancements in technology.

Among the distinctive technologies used by Friedrich Racervmn is their proprietary manufacturing process, which integrates automation and robotics to enhance efficiency and precision. This not only speeds up production times but also ensures that the products maintain a consistently high quality. The use of Computer Numerical Control (CNC) machines in their processes allows for intricate designs and complex geometries that meet rigorous industry standards.

Moreover, Friedrich Racervmn utilizes innovative materials in their products to ensure durability and performance under various conditions. These materials are selected based on their specific properties, such as strength, weight, and resistance to environmental factors, ensuring that the final output exceeds customer expectations.

Another hallmark of Friedrich Racervmn is their commitment to sustainability. The company actively seeks ways to minimize its environmental footprint by optimizing resource use and incorporating eco-friendly practices throughout its manufacturing processes. This is reflected in their efforts to design products that are not only high-performing but also energy-efficient, helping customers reduce their carbon emissions.

Friedrich Racervmn’s customer service stands out as well. Their team is dedicated to providing exceptional support, ensuring that clients receive personalized attention and solutions tailored to their unique needs. This customer-centric approach is a fundamental part of their philosophy and has contributed to building strong and lasting relationships within the industry.

In summary, Friedrich Racervmn is a leader in precision engineering, recognized for its advanced technologies, innovative manufacturing processes, commitment to sustainability, and outstanding customer service. The company’s focus on quality and innovation positions it as a vital player in the modern industrial landscape, continuously pushing the envelope toward a more technologically advanced and environmentally conscious future.