Safety Precautions

Tool operators and maintenance personnel must always comply with the safety precautions given in this manual and on the stickers and tags attached to the tool and hose.

These safety precautions are given for your safety. Re- view them carefully before operating the tool and before performing general maintenance or repairs.

Supervising personnel should develop additional pre- cautions relating to the specific work area and local safety regulations. If so, place the added precautions in the space provided in this manual.

The model HD01 Hydraulic Hammer Drill will provide safe and dependable service if operated in accordance with the instructions given in this manual. Read and un- derstand this manual and any stickers and tags attached to the tool and hose before operation. Failure to do so could result in personal injury or equipment damage.

•The operator must start in a work area without by- standers. Flying debris can cause serious injury.

•Do not operate the tool unless thoroughly trained or under the supervision of an instructor. Establish a training program for all operators to ensure safe operation.

•Always wear personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hear- ing protection used for appropriate conditions will reduce personal injuries.

•Remove any adjusting key or wrench before turning the tool on. A wrench or key left attached to a rotat- ing part of the tool may result in personal injury.

•The operator must be familiar with all prohibited work areas such as excessive slopes and danger- ous terrain conditions.

•Do not change accessories, make adjustments, in- spect, clean or replace any part(s) if the hydraulic power source is connected. Accidental engagement of the tool can cause serious injury.

•Always connect hoses to the tool hose couplers be- fore energizing the hydraulic power source. Be sure all hose connections are tight and are in good condi- tion.

•Do not operate the tool at oil temperatures above 140 °F/60 °C. Operation at higher temperatures can cause higher than normal temperatures at the tool which can result in operator discomfort.

•Do not operate a damaged, improperly adjusted, or incompletely assembled hammer drill.

•Never wear loose clothing that can get entangled in the working parts of the tool.

•Keep all parts of your body away from the drill and maintain proper footing and balance at all times.

•When working near electrical conductors, always assume that all conductors are energized and that insulation, clothing and hoses can conduct electric- ity. Stay a safe distance away from electrical con- ductors.

•Do not operate tool in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

•Keep cutting tools sharp and clean. Properly main- tained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

•Keep a firm grip on the tool at all times. Do not at- tempt to operate this tool without holding it with both hands. It is recommended that the side handle be used at all times. Operating this tool with one hand will result in loss of control. Tighten the side handle securely before use.

•Never lay the tool down until the bit has come to a complete stop. Moving bits could cause injury.

•Wear gloves when operating tool or changing bits. Accessible metal parts on the tool and bits may get extremely hot during operation.

•If the hydraulic power supply has been interrupted, place the hammer drill in the OFF position before restarting the hydraulic power supply.

•To avoid personal injury or equipment damage, all tool repair, maintenance and service must only be performed by authorized and properly trained per- sonnel.

•Warning: Use of this tool on certain materials during demolition could generate dust potentially contain- ing a variety of hazardous substances such as as- bestos, silica or lead. Inhalation of dust containing these or other hazardous substances could result in serious injury, cancer or death. Protect yourself and those around you. Research and understand the materials you are cutting. Follow correct safety procedures and comply with all applicable national, state or provisional health and safety regulations relating to them, including, if appropriate arranging for the safe disposal of the materials by a qualified person.

•

HD01 User Manual ◄ 5

HD01 specifications

Stanley Black & Decker has long been a trusted name in the tools and home improvement industry, and the HD01 model is a testament to the company’s commitment to excellence and innovation. The HD01 is a high-performance power tool that caters to both professionals and DIY enthusiasts, offering a blend of user-friendly features and cutting-edge technologies.

One standout feature of the Stanley Black & Decker HD01 is its powerful motor, designed to deliver impressive torque and speed, making it suitable for a variety of applications, from drilling into tough materials to driving screws with precision. This motor enables the HD01 to work efficiently in both heavy-duty and lighter tasks, ensuring versatility for users.

The design of the HD01 ensures comfort and control. Its ergonomic grip allows for extended use without causing unnecessary strain on the user’s hands. Furthermore, the tool's lightweight construction makes it easy to handle, even in tight spaces or when working overhead. These features are pivotal in ensuring that users can work for longer periods without fatigue.

In terms of technology, the HD01 incorporates a brushless motor, which not only improves the tool's longevity but also enhances performance. Brushless motors are known for their efficiency, translating to longer run times and reduced maintenance. This is an advantage that professionals, in particular, will appreciate, as it minimizes downtime on job sites.

Another characteristic of the HD01 is its variable speed settings, allowing users to adapt the tool’s performance to match the specific requirements of the task at hand. This feature enhances precision and control, whether the need is for a slow, steady approach or a rapid, powerful output.

The HD01 also comes equipped with advanced battery technology that provides longer run times and faster charging capabilities, ensuring that users can stay productive throughout their projects. The inclusion of an LED work light further amplifies its user-friendliness, illuminating work areas in low-light conditions and enhancing overall visibility.

In summary, the Stanley Black & Decker HD01 is a powerful, versatile, and user-centric tool designed to meet the needs of a diverse range of users. Its blend of innovative technologies and practical features makes it an essential addition to any toolkit, whether in the hands of a seasoned professional or a budding DIYer. With the HD01, Stanley Black & Decker continues to uphold its legacy of quality and innovation in power tools.