Stanley Black & Decker HD45 user manual Charging the Accumulator, Accumulator Testing Procedure

Page 12

CHARGING THE ACCUMULATOR

ACCUMULATOR TESTING

PROCEDURE

To check or charge the accumulator the following equip- ment is required:

31254 Charge Kit: which includes the following.

•Accumulator Tester (Part Number 02835).

•Charging Assembly (Part Number 15304).

(P/N 15304 includes a liquid filled gauge with snub valve, hose and fittings.)

•NITROGEN bottle with an 1000 psi/70 bar minimum charge. (Not included in 31254 Charge Kit.)

1.Remove the valve cap assembly from the hammer drill.

2.Holding the chuck end of Accumulator Tester (Part Number 02835) turn the gauge fully counterclock- wise to ensure that the stem inside the chuck is completely retracted.

3.Thread the tester onto the accumulator charg- ing valve. Do not advance the gauge-end into the chuck-end. Turn as a unit. Seat the chuck on the accumulator charging valve and hand tighten only.

4.Advance the valve stem of the tester by turning the gauge-end clockwise until a pressure is read on the gauge (charge pressure should be 500-700 psi/34- 48 bar).

5.If pressure is OK unscrew the gauge-end from the chuck to retract the stem, then unscrew the entire tester assembly from the accumulator charging valve. If pressure is low, charge the accumulator as described in the following procedure.

6.Install the protective valve cap assembly.

ACCUMULATOR CHARGING

1.Perform steps 1 through 4 of the accumulator test- ing procedure above.

2.Connect the chuck of the charging assembly to the charging valve on the accumulator tester or, if pre- ferred, remove the tester from the charging valve and connect the charging assembly chuck directly to the charging valve.

3.Adjust the regulator to the charging pressure of 600 psi/42 bar.

NOTE:

It may be necessary to set the gauge at 650-700 psi/45-48 bar to overcome any pressure drop through the charging system.

4. Open the valve on the charging assembly hose.

IMPORTANT

If the underwater model is to be used at depths greater than 300 ft/91 m, increase the accumulator charge 40 psi/3 bar for each 100 ft/30 m of depth to offset water pressure.

5.When the accumulator is fully charged close the valve on the charging assembly hose and remove the charging assembly chuck from the accumulator tester or tool charging valve.

6.If the accumulator tester has been used, be sure to turn the gauge-end fully counterclockwise before re- moving the tester from the charging valve of the tool.

7.Replace the valve cap assembly.

GENERAL SERVICE NOTES

1.If the hammer drill is repainted after servicing, be sure to mask off the vent in the valve cap assembly. Do not allow paint to enter the IN and OUT ports or the bore of the motor assembly.

2.If the handle grips need to be replaced.

a.Remove the old grips and clean the handle.

b.Wash the new grips and the handle clean and dry, simply push or drive the grips on. DO NOT lubricate the parts. The grips will not be secure on the handle if any grease or oil is used.

12 ► HD45 User Manual

Page 11 Page 13
Image 12
Page 11 Page 13
Contents HD45 Declaration of Conformity Weisbeck, AndyTable of Contents Safety Symbols Local Safety RegulationsSafety Precautions Tool Stickers & Tags Stanley Hydraulic toolsHose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsPreoperation Procedures BIT InstallationOperation Drill OperationUnderwater Model Preventative Maintenance Cold Weather OperationAccumulator Testing Procedure General Service NotesCharging the Accumulator Accumulator ChargingCharging the Accumulator Tool Protection & Care Troubleshooting Problem Cause SolutionAccessories SpecificationsHD45 Parts Illustration HD45 Parts List Part QTY DescriptionUnderwater Tools Depth Guideline Underwater Models only
Related manuals
Manual 24 pages 1010 b

HD45 specifications

The Stanley Black & Decker HD45 is a powerful and versatile tool designed for professionals and DIY enthusiasts alike. This rugged and durable hammer drill is engineered to handle a variety of tasks, making it a go-to solution for both construction sites and home improvement projects. With a focus on performance, practicality, and safety, the HD45 brings together innovative features and advanced technologies to deliver exceptional results.

One of the standout features of the HD45 is its robust motor, which delivers high torque and variable speeds, allowing users to drill through various materials such as wood, fiberglass, and metal with ease. The drill's two-speed settings enable users to switch between high-speed drilling and high-torque applications, providing versatility for different types of jobs. This adaptability ensures that the HD45 can take on challenging tasks without compromising on efficiency.

Another important characteristic of the HD45 is its ergonomic design. The drill is equipped with a comfortable, non-slip grip that allows for better control during operation, reducing user fatigue over extended use. Additionally, the compact and lightweight construction makes it easy to maneuver in tight spaces, which is particularly helpful when working on intricate projects or reaching overhead.

The HD45 also integrates several advanced technologies to enhance its usability and performance. One such technology is the electronic clutch, which provides precise control over torque settings. This feature prevents overdriving screws and allows for consistent results across various materials. Furthermore, the built-in LED work light illuminates the workspace, providing visibility in dimly lit areas and ensuring accurate drilling every time.

Safety is a top priority for Stanley Black & Decker, and the HD45 reflects this commitment. The drill is equipped with a robust safety switch that prevents accidental startups, ensuring that users can handle the tool with confidence. Additionally, the durable housing of the drill is designed to withstand heavy-duty use, offering longevity and reliability on the job.

In conclusion, the Stanley Black & Decker HD45 is a high-performance hammer drill that combines power, versatility, and safety features. With its advanced motor, ergonomic design, and innovative technologies, it is an indispensable tool for anyone looking to tackle a wide range of drilling and fastening tasks. Whether for professional construction or home improvement, the HD45 is ready to deliver outstanding results.
Top Page Image Contents