Friedrich MW30C3G, MW36C3G, MR30C3G, MR36C3G operation manual Cleaning and Care

Page 13

CLEANING AND CARE

 

●

Before cleaning the air conditioner, be sure to turn it off and disconnect the Power Supply Cord.

CAUTION!

●

Be sure the Intake Grille (Fig. 1 8) is installed securely.

●When removing and replacing the air filters, be sure not to touch the heat exchanger, as personal injury may result.

Cleaning the Intake Grille

1.Remove the Intake Grille.

1 Place your fingers at both lower ends of the grille panel, and lift forward; if the grille seems to catch partway through its movement, continue lifting upward to remove.

2Pull past the intermediate catch and open the Intake Grille wide so that it become horizontal.

Intake Grille

2 2

1 1

Intake Grille

Mounting shaft

Knob

2. Clean with water.

Remove dust with a vacuum cleaner; wipe the unit with warm water, then dry with a clean, soft cloth.

3. Replace the Intake Grille.

1Pull the knobs all the way.

2Hold the grille horizontal and set the left and right mounting shafts into the bearings at the top of the panel.

3Press the place where the arrow on the diagram indicates and close the Intake Grille.

 

Mounting shaft

Intake

Bearing

Grille

2

 

1

 

Knob

Intake Grille

 

Mounting shaft

Knob

Cleaning the Air Filter

1. Open the Intake Grille, and remove the air filter.

Lift up the air filter’s handle, disconnect the two lower tabs, and pull out.

Air filter handle

Hooks (two places)

2. Remove dust with a vacuum cleaner or by washing.

After washing, allow to dry thoroughly in a shaded place.

3.Replace the Air Filter and close the Intake Grille.

1 Align the sides of the air filter with the panel, and push in fully, making sure the two lower tabs are returned properly to their holes in the panel.

Hooks (two places)

2Close the Intake Grille.

(For purposes of example, the illustration shows the unit without Intake Grille installed.)

●Dust can be cleaned from the air filter either with a vacuum cleaner, or by washing the filter in a solution of mild detergent and warm water. If you wash the filter, be sure to allow it to dry thoroughly in a shady place before reinstalling.

●If dirt is allowed to accumulate on the air filter, air flow will be reduced, lowering operating efficiency and increasing noise.

●During periods of normal use, the Air Filters should be cleaned every two weeks.

●When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service personnel.

●When cleaning the unit’s body, do not use water hotter than 104°F, harsh abrasive cleansers, or volatile agents like benzene or thinner.

●Do not expose the unit body to liquid insecticides or hairsprays.

●When shutting down the unit for one month or more, first allow the fan mode to operate continuously for about one-half day to allow internal parts to dry thoroughly.

En-12

9315345394_OM.indb 12

9/30/2010 2:44:25 PM

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Español Français English Operating Manual Mode D’EMPLOI Manual DE FuncionamientoSafety Precautions ContentsInverter Removable Open Panel Features and FunctionsManual Auto Name of PartsEn-4 Preparation Operation To Select Mode Operation Press the START/STOP button PTo Set the Thermostat Press the SET TEMP. button K To Set the Fan Speed Press the FAN Control button OTo Stop Operation Press the START/STOP button P About Mode OperationAbout Auto Changeover Operation Timer Operation To Change the Timer Settings Sleep Timer OperationAbout the Sleep Timer Manual Auto OperationRemote Controller’s display does not change Adjusting the Direction of AIR CirculationTo select Swing Operation Press the Swing button S Swing OperationAbout Swing Operation Cleaning and Care Symptom Problem TroubleshootingOperating Tips Event of Power InterruptionAuto Restart Temperature and Humidity Range SpecificationCooling Mode Dry Mode Outdoor temperature Indoor temperature9315345394OM.indb 30/2010 24425 PM 9315345394OM.indb 30/2010 24434 PM 9315345394OM.indb 30/2010 24434 PM 9315345394OM.indb 30/2010 24434 PM

MR36C3G, MR30C3G, MW30C3G, MW36C3G specifications

Friedrich air conditioners are renowned for their innovative features and reliable performance, especially in the models MW30C3G, MR36C3G, MR30C3G, and MW36C3G. These products cater to various cooling needs, providing ideal solutions for both home and commercial settings.

The MW30C3G window air conditioner, for instance, boasts an impressive cooling capacity that effectively tackles high temperatures, making it suitable for larger rooms. It comes equipped with a programmable timer and a remote control, offering convenience and energy management for users. The multi-speed fan settings allow for customizable airflow, ensuring a comfortable environment at all times.

On the other hand, the MR36C3G model is a versatile mini-split system designed for energy efficiency and performance. It features an inverter technology that adjusts the compressor speed according to the cooling demand, resulting in lower energy consumption and quieter operation. Additionally, the MR36C3G includes a smart sensor that detects occupancy and automatically adjusts the temperature, enhancing comfort and efficiency.

The MR30C3G air conditioner is known for its sleek design and powerful cooling performance. With multiple cooling modes and dehumidification functionality, it can maintain a comfortable indoor climate even during high humidity periods. Its robust build ensures durability, making it an excellent long-term investment for homeowners and business owners alike.

Lastly, the MW36C3G model is characterized by its compact size and high energy efficiency rating. It is equipped with features like a washable filter, which simplifies maintenance and helps maintain clean air quality. The user-friendly interface allows for easy adjustments, while the quiet operation ensures minimal disruption in living spaces.

Collectively, those models from Friedrich represent a blend of modern technology and practicality. Their emphasis on energy efficiency, user comfort, and design will appeal to a variety of consumers seeking reliable cooling solutions. Whether opting for a window unit or a mini-split system, users can trust Friedrich’s commitment to quality and performance.
Top Page Image Contents