Lincoln Electric IM716 manual Safety, Power Wave

Page 2

i

SAFETY

i

WARNING

CALIFORNIA PROPOSITION 65 WARNINGS

Diesel engine exhaust and some of its constituents are known to the State of California to cause can- cer, birth defects, and other reproductive harm.

The Above For Diesel Engines

The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

The Above For Gasoline Engines

ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH. KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.

Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box 351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.

BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE PERFORMED ONLY BY QUALIFIED INDIVIDUALS.

FOR ENGINE powered equipment.

1.a. Turn the engine off before troubleshooting and maintenance work unless the maintenance work requires it to be running.

____________________________________________________

1.b. Operate engines in open, well-ventilated areas or vent the engine exhaust fumes

outdoors.

____________________________________________________

1.c. Do not add the fuel near an open flame welding arc or when the engine is running.

Stop the engine and allow it to cool before refueling to prevent spilled fuel from vaporiz- ing on contact with hot engine parts and igniting. Do not spill fuel when filling tank. If fuel is spilled, wipe it up and do not start engine until fumes have been eliminated.

____________________________________________________

1.d. Keep all equipment safety guards, covers and devices in position and in good repair.Keep hands, hair, clothing and tools away from V-belts, gears, fans and all other moving parts when starting, operating or repairing equipment.

____________________________________________________

1.e. In some cases it may be necessary to remove safety guards to perform required maintenance. Remove guards only when necessary and replace them when the maintenance requiring their removal is complete. Always use the greatest care when working near moving parts.

___________________________________________________

1.f. Do not put your hands near the engine fan. Do not attempt to override the governor or idler by pushing on the throttle control rods

while the engine is running.

___________________________________________________

1.g. To prevent accidentally starting gasoline engines while turning the engine or welding generator during maintenance work, disconnect the spark plug wires, distributor cap or magneto wire as appropriate.

1.h. To avoid scalding, do not remove the radiator pressure cap when the engine is hot.

ELECTRIC AND MAGNETIC FIELDS may be dangerous

2.a. Electric current flowing through any conductor causes localized Electric and Magnetic Fields (EMF). Welding current creates EMF fields around welding cables and welding machines

2.b. EMF fields may interfere with some pacemakers, and welders having a pacemaker should consult their physician before welding.

2.c. Exposure to EMF fields in welding may have other health effects which are now not known.

2.d. All welders should use the following procedures in order to minimize exposure to EMF fields from the welding circuit:

2.d.1. Route the electrode and work cables together - Secure them with tape when possible.

2.d.2. Never coil the electrode lead around your body.

2.d.3. Do not place your body between the electrode and work cables. If the electrode cable is on your right side, the work cable should also be on your right side.

2.d.4. Connect the work cable to the workpiece as close as possible to the area being welded.

2.d.5. Do not work next to welding power source.

Mar ‘95

POWER WAVE 455

Page 1 Page 3
Image 2
Page 1 Page 3
Contents Power Wave 455/STT Safety Power WaveElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Table of Contents Installation Technical Specifications Power Wave 455/STT K1518-4Input Connection Machine GroundingHigh Frequency Protection LiftingTable A.1 Input Fuse and Supply Wire ConsiderationsElectrode and Work Cable Connections Minimum CopperCable INDUCTANCE, and ITS Effects on Pulse Welding Negative Electrode PolarityVoltage Sensing Electrode Voltage Sensing Table A.2Work Voltage Sensing System Description System ModelBasic Rules Simple SystemMultiple Group System Single Group Multi-Head SystemFigure A.11 Single Group Multi-Head System Alternate MethodTWO Power Waves Figure A.2Multiple ARC Sense Lead and Work Lead Placement Guidelines BADDIP Switch Settings and Locations Receptacle SpecificationsPower Wave Watercooler Field Installed Option Control Board DIP Switch1OPERATIONB-1 Electric Shock can killPower Wave 455/STT Recommended Processes and Equipment OperationGeneral Description Required EquipmentCase Front Layout Power Wave 455/STT North American Canadian Case Front ControlsWelding Adjustments Nominal ProceduresFringe Procedures Making a WeldARC Control Welding ModeVolts / Trim Non Synergic CV Constant Voltage WeldingSynergic CV All CV ModesPulse Welding Figure A.6 Current Wave Form PulseTrim STT WeldingField Installed AccessoriesFactory Installed Optional EquipmentMaintenance Routine MaintenanceTroubleshooting HOW to USE Troubleshooting GuideUsing the Status LED to Troubleshoot System Problems Error code before the machine is turned offError Codes for the Powerwave Error Code # IndicationContact your local Lincoln Troubleshooting GuideAuthorized Field Service Facility If the Thermal LED is also lit Exceeding the 325 amp limit on STT output terminal Your local Lincoln Authorized Field Service Facility Power Wave 455/STT Wiring Diagram Connection Diagram Connection Diagram Semi-automatic Simple SystemDiagrams Work Sense Control Cable K1543Dimension Print Power Wave Power Wave 455/STT Precaucion Warnung

IM716 specifications

The Lincoln Electric IM716 is a state-of-the-art multi-process welding machine that stands out in the industry for its versatility and advanced technology. Designed for professionals who seek efficiency and precision, the IM716 is capable of handling various welding processes, including MIG, TIG, and Stick welding, making it an excellent option for a wide range of applications, from automotive repairs to heavy industrial work.

One of the key features of the IM716 is its intuitive interface, which includes a digital display that simplifies the settings adjustments. Users can easily select the desired welding mode, adjust the voltage and wire feed speed, and monitor their performance all from a user-friendly control panel. This ease of use significantly reduces setup time, allowing welders to focus more on the task at hand than on navigating complicated controls.

The IM716 employs Lincoln Electric's advanced inverter technology, which provides greater energy efficiency compared to traditional transformer-based machines. This innovative technology not only reduces power consumption but also contributes to a more consistent arc quality. The inverter design also makes the machine lighter and more portable, accommodating the needs of welders who move between job sites.

Another notable characteristic of the IM716 is its robust construction. Designed for durability, the machine can withstand the rigors of a demanding work environment. It features a rugged steel housing that protects internal components from damage while enhancing its longevity. Additionally, the IM716 operates reliably in various conditions, including extreme temperatures, making it a dependable choice for outdoor welding projects.

The IM716 is equipped with advanced safety features, including a thermal overload protection system that prevents overheating during intense welding tasks. This feature extends the lifespan of the machine and ensures safe operation for users. Furthermore, the IM716 includes features like a built-in gas solenoid valve for TIG welding, providing added convenience by enabling automatic gas flow control.

In conclusion, the Lincoln Electric IM716 is a powerful, versatile, and well-engineered welding machine that meets the needs of professional welders. With its multi-process capabilities, user-friendly interface, advanced inverter technology, and durable construction, it exemplifies innovation in the welding industry. Whether for fabricating, repairing, or maintenance tasks, the IM716 stands out as a reliable and efficient choice for any welding operation.
Top Page Image Contents