Friedrich WE16, WE13, WE10, WS08, WS16, WS14, WY13, WY10 Installation requirements, Sleeve installation

Page 11

 

 

 

920-007-13

 

Installation requirements

 

 

STEP 1

The WSC SLEEVE should be positioned so that the

STEP 4 The WSC SLEEVE must also be installed with a downward

 

 

DRAIN EXTENSION extends a minimum of 9⁄16" beyond

tilt toward the outside of the building. If a level is placed

 

 

the OUTSIDE WALL (See Figure 7).

so that it rests on the FRONT and BACK UNIT REST as

STEP 2

The WSC SLEEVE must extend a minimum of ⅞" beyond

shown in Figure 8, a properly installed unit provides a ½

bubble slope to the outside of the building.

 

 

the INSIDE WALL.

CAUTION: SLEEVE projections and leveling precautions

STEP 3

The WSC SLEEVE must be installed level side to side.

must be observed to prevent the entry of water into the room.

Figure 8

Raised Ledge

Back Unit Rest

 

Level

Front Unit Rest

Sleeve installation

STEP 1 After unpacking the WSC SLEEVE from the carton, remove the corrugated FRONT PANEL. Place the WSC SLEEVE in the wall opening following the instructions given in the INSTALLATION REQUIREMENTS. Attach the SLEEVE to the INSIDE WALL by driving two #12A x 2" screws in each side of the SLEEVE (see Figure 7). Shim at the top of the SLEEVE, midway between the sides. Drive one #12A x 2" screw in the top of the sleeve, close to the shim. Install screws from inside the SLEEVE. If the wall opening is not framed with wood, use expansion anchor bolts or molly (toggle) bolts (not provided).

STEP 2 Once the SLEEVE has been installed, check the LEVEL again to be sure the ½ bubble downward tilt is maintained. Apply shims, if required, to maintain the proper slope.

STEP 3 Caulk the perimeter of the entire opening on the inside and the outside between the SLEEVE and the WALL.

STEP 4 The corrugated front panel removed in Step 1 above must be remounted back in place if masonry work is to be done and/or if the "WallMaster" CHASSIS is to be installed at a later date.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Thru-the-wall Table of Contents Electrical Data Welcome to years of economical comfortHow to operate your Friedrich room air conditioner Automatic component protection Using the remote controlDecorative Front How to clean the air filterElectrical requirements How to change airflow directionHow to cover inner weather panel holes Never use an extension cord Power cord informationTroubleshooting tips and home maintenance Wall preparation Installation instructions for WSC sleeveMounting hardware provided Sleeve installation Installation requirementsCondenser Shroud 920-007-13 Chassis Seal Gasket Installation After IDK Interior Drain Kit Condensate removal WS, WE and WY modelsAlternate drain kits DK Drain KitWALLMASTER≤ THRU-THE-WALL AIR Conditioners Limited Warranty Your personal warranty registration record 920-007-13 920-007-13 Friedrich AIR Conditioning CO

WY13, WS13, WY10, WE10, WS14 specifications

Friedrich, a well-known name in the realm of climate control, has consistently pushed the boundaries of innovation with its WS08, WS16, WE13, WS10, and WE16 models. These units, designed primarily for residential and commercial use, represent a blend of efficiency, modern technology, and user-centric features that cater to diverse cooling and heating needs.

The WS08 and WS10 models are particularly celebrated for their compact size and powerful cooling capabilities. They are ideal for smaller spaces, making them perfect for apartments, offices, or utility areas. These portable air conditioning units stand out with their advanced energy efficiency ratings, helping users save on electricity bills while still enjoying a comfortable environment. Equipped with a user-friendly interface, the WS models allow users to set their desired temperature easily and choose between various fan speeds to optimize airflow for personal comfort.

In contrast, the WS16 provides enhanced performance due to its larger capacity. It is capable of cooling larger areas effectively, making it a suitable choice for living rooms or larger commercial spaces. One of its key features is the Smart Wi-Fi technology, which enables users to control the unit remotely through a dedicated app. This convenience allows for pre-cooling an area before arriving home, ensuring optimal comfort with minimal effort.

The WE13 and WE16 models are particularly noteworthy for their dual-functionality, providing both cooling and heating options. This versatility is perfect for regions that experience varied climates, allowing for year-round usage. The WE series is equipped with innovative inverter technology, which helps adjust the compressor speed based on the desired temperature. This smart feature improves energy efficiency and reduces noise levels, facilitating a quieter environment.

Additionally, both WE models feature advanced air filtration systems that capture dust, pollen, and other allergens, contributing to better indoor air quality. Their sleek designs and whisper-quiet operation make them ideal for bedrooms and other noise-sensitive areas.

In conclusion, whether it’s the compact efficiency of the WS08 and WS10 or the powerful flexibility of the WS16 and WE series, Friedrich’s offerings meet diverse cooling and heating needs with enhanced technology and user-friendly features. These units not only focus on performance but also prioritize energy efficiency and air quality, making them an excellent choice for any climate control requirement.
Top Page Image Contents