Friedrich WE10, WE13, WE16, WS08, WS16, WS14, WY13, WY10, WS10, WS13 operation manual Condenser Shroud

Page 12

920-007-13

WallMaster chassis installation instructions for WS, WE and WY models (WSC-A sleeve)

These instructions are provided for installation of WallMaster air conditioner chassis models into thru-the-wall sleeves. This chassis has been UL approved with the sleeve listed on the serial nameplate of this chassis. Important warranty information is provided on pages 17 and 18. Keep these instructions in a convenient location for any warranty service that may be required.

STEP 1 Check the sleeve to be certain it has been correctly installed in the wall. Remove the corrugated front panel on the WSC SLEEVE. Remove the rear WEATHER PANEL. Reverse grille. Place lower edge into sleeve tab (Friedrich logo facing out). Align slots with screw holes. Secure grille with screws.

A.Check the anchor screws. There should be four

(4) in the WSC SLEEVE (two in each side).

B.Determine if the sleeve has a downward slope, to the outside, of ½ bubble on a level. See page 10 for further details.

C.Check to be sure the sleeve has been sealed around all edges with an industrial type caulking on both the outside and inside to prevent rain entry.

STEP 2 Check the electrical receptacle to see that it conforms to the requirements for the chassis model to be installed. See pages 2 and 5, for the receptacle requirements.

STEP 3 The decorative front is packaged in a separate box inside the chassis shipping carton, between the chassis and the carton. Remove this box and set the box aside until later.

STEP 4 With the help of an assistant, remove the chassis from the shipping carton. Be careful not to allow anything to impact against the hairpins as this may result in damage to them. With the help of an assistant, lift the chassis by the basepan and slide it into the sleeve until it contacts the rear grille. With the chassis in proper position, the front edge of the basepan must extend out 4 ¾ inches from the front (side) edge of sleeve.

Figure 9

Condenser

Shroud

MODEL#WS07A10BAB123456C3567

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Thru-the-wall Table of Contents Welcome to years of economical comfort Electrical DataHow to operate your Friedrich room air conditioner Using the remote control Automatic component protectionHow to clean the air filter Decorative FrontHow to change airflow direction How to cover inner weather panel holesElectrical requirements Power cord information Never use an extension cordTroubleshooting tips and home maintenance Installation instructions for WSC sleeve Mounting hardware providedWall preparation Installation requirements Sleeve installationCondenser Shroud 920-007-13 Chassis Seal Gasket Installation After Condensate removal WS, WE and WY models Alternate drain kitsDK Drain Kit IDK Interior Drain KitWALLMASTER≤ THRU-THE-WALL AIR Conditioners Limited Warranty Your personal warranty registration record 920-007-13 920-007-13 Friedrich AIR Conditioning CO

WY13, WS13, WY10, WE10, WS14 specifications

Friedrich, a well-known name in the realm of climate control, has consistently pushed the boundaries of innovation with its WS08, WS16, WE13, WS10, and WE16 models. These units, designed primarily for residential and commercial use, represent a blend of efficiency, modern technology, and user-centric features that cater to diverse cooling and heating needs.

The WS08 and WS10 models are particularly celebrated for their compact size and powerful cooling capabilities. They are ideal for smaller spaces, making them perfect for apartments, offices, or utility areas. These portable air conditioning units stand out with their advanced energy efficiency ratings, helping users save on electricity bills while still enjoying a comfortable environment. Equipped with a user-friendly interface, the WS models allow users to set their desired temperature easily and choose between various fan speeds to optimize airflow for personal comfort.

In contrast, the WS16 provides enhanced performance due to its larger capacity. It is capable of cooling larger areas effectively, making it a suitable choice for living rooms or larger commercial spaces. One of its key features is the Smart Wi-Fi technology, which enables users to control the unit remotely through a dedicated app. This convenience allows for pre-cooling an area before arriving home, ensuring optimal comfort with minimal effort.

The WE13 and WE16 models are particularly noteworthy for their dual-functionality, providing both cooling and heating options. This versatility is perfect for regions that experience varied climates, allowing for year-round usage. The WE series is equipped with innovative inverter technology, which helps adjust the compressor speed based on the desired temperature. This smart feature improves energy efficiency and reduces noise levels, facilitating a quieter environment.

Additionally, both WE models feature advanced air filtration systems that capture dust, pollen, and other allergens, contributing to better indoor air quality. Their sleek designs and whisper-quiet operation make them ideal for bedrooms and other noise-sensitive areas.

In conclusion, whether it’s the compact efficiency of the WS08 and WS10 or the powerful flexibility of the WS16 and WE series, Friedrich’s offerings meet diverse cooling and heating needs with enhanced technology and user-friendly features. These units not only focus on performance but also prioritize energy efficiency and air quality, making them an excellent choice for any climate control requirement.
Top Page Image Contents