Friedrich WS16, WE13, WE16, WE10, WS08, WS14, WY13, WY10, WS10 Chassis Seal Gasket Installation After

Page 14

920-007-13

STEP 5 CHASSIS SEAL GASKET INSTALLATION: After

STEP 6 Remove the intake grille from the decorative front frame by

installing the shell, slide the chassis into the shell stopping

grasping it at the upper right and left side corners. Pull out

approximately 3" from full insertion. Stuff the chassis seal

until the grille is released from the upper retaining snaps.

gasket one inch deep between the chassis and the shell

Tilt it down toward you, lift up and out of the bottom retaining

(see Figure 11). Make sure the gasket is installed beginning

snaps. Install the decorative front frame in place over the

from the lower right side corner and extending over the

sleeve opening and attach it to the chassis with four sheet

top and down to the lower left side corner. Then push the

metal screws as shown in Figure 11. Replace the intake

chassis all the way into the shell for the remaining distance

grille by positioning the bottom of the grille into the bottom

so that the plastic front meets the front edge of the shell.

retaining snaps. Tilt the front up and away from you. Press

If chassis seal gasket is not installed, the operation of the

in lightly on top, and the grille will position itself into upper

retaining snaps.

unit will be negatively affected. Also, the operation noise

 

and outside noise will be amplified.

 

Chassis Seal

Gasket

Decorative Front

AB123456C3567

WS07A10B

MODEL#

Screws (4)

Return Air

Grille

Attach the frame to the chassis by installing four (4) 8A-5/8" screws through the slots in the frame and into the holes in the chassis.

Figure 11

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Thru-the-wall Table of Contents Welcome to years of economical comfort Electrical DataHow to operate your Friedrich room air conditioner Using the remote control Automatic component protectionHow to clean the air filter Decorative FrontElectrical requirements How to change airflow directionHow to cover inner weather panel holes Power cord information Never use an extension cordTroubleshooting tips and home maintenance Wall preparation Installation instructions for WSC sleeveMounting hardware provided Installation requirements Sleeve installationCondenser Shroud 920-007-13 Chassis Seal Gasket Installation After DK Drain Kit Condensate removal WS, WE and WY modelsAlternate drain kits IDK Interior Drain KitWALLMASTER≤ THRU-THE-WALL AIR Conditioners Limited Warranty Your personal warranty registration record 920-007-13 920-007-13 Friedrich AIR Conditioning CO

WY13, WS13, WY10, WE10, WS14 specifications

Friedrich, a well-known name in the realm of climate control, has consistently pushed the boundaries of innovation with its WS08, WS16, WE13, WS10, and WE16 models. These units, designed primarily for residential and commercial use, represent a blend of efficiency, modern technology, and user-centric features that cater to diverse cooling and heating needs.

The WS08 and WS10 models are particularly celebrated for their compact size and powerful cooling capabilities. They are ideal for smaller spaces, making them perfect for apartments, offices, or utility areas. These portable air conditioning units stand out with their advanced energy efficiency ratings, helping users save on electricity bills while still enjoying a comfortable environment. Equipped with a user-friendly interface, the WS models allow users to set their desired temperature easily and choose between various fan speeds to optimize airflow for personal comfort.

In contrast, the WS16 provides enhanced performance due to its larger capacity. It is capable of cooling larger areas effectively, making it a suitable choice for living rooms or larger commercial spaces. One of its key features is the Smart Wi-Fi technology, which enables users to control the unit remotely through a dedicated app. This convenience allows for pre-cooling an area before arriving home, ensuring optimal comfort with minimal effort.

The WE13 and WE16 models are particularly noteworthy for their dual-functionality, providing both cooling and heating options. This versatility is perfect for regions that experience varied climates, allowing for year-round usage. The WE series is equipped with innovative inverter technology, which helps adjust the compressor speed based on the desired temperature. This smart feature improves energy efficiency and reduces noise levels, facilitating a quieter environment.

Additionally, both WE models feature advanced air filtration systems that capture dust, pollen, and other allergens, contributing to better indoor air quality. Their sleek designs and whisper-quiet operation make them ideal for bedrooms and other noise-sensitive areas.

In conclusion, whether it’s the compact efficiency of the WS08 and WS10 or the powerful flexibility of the WS16 and WE series, Friedrich’s offerings meet diverse cooling and heating needs with enhanced technology and user-friendly features. These units not only focus on performance but also prioritize energy efficiency and air quality, making them an excellent choice for any climate control requirement.
Top Page Image Contents