Wilton 2221VS Machinery general safety warnings, When setting up machine, When using machine

Page 5

-Misuse of this machine can cause serious injury.

-For safety, machine must be set up, used and serviced properly.

-Read, understand and follow instructions in the Operating Instructions and Parts Manual which was shipped with your machine.

When setting up machine:

-Always avoid using machine in damp or poorly lighted work areas.

-Always be sure the machine support is securely anchored to the floor or the work bench.

When using machine:

-Always wear safety glasses with side shields (See ANSI Z87.1)

-Never wear loose clothing or jewelry.

-Never overreach—you may slip and fall.

When servicing machine:

- Always disconnect the machine from its electrical

supply while servicing.

-Always follow instructions in Operating Instructions and Parts Manual when changing accessory tools or parts.

-Never modify the machine without consulting Wilton Corporation.

You—the stationary power tool user— hold the key to safety.

Read and follow these simple rules for best results and full benefits from your machine. Used properly, Wilton’s machinery is among the best in design and safety. However, any machine used improperly can be rendered inefficient and unsafe. It is absolutely mandatory that those who use our products be properly trained in how to use them correctly. They should read and understand the Operating Instruc- tions and Parts Manual as well as all labels affixed to the machine. Failure in following all of these warnings can cause serious injuries.

Machinery general safety warnings

1.Always wear protective eye wear when operating machinery. Eye wear shall be impact resistant, protective safety glasses with side shields which comply with ANSI Z87.1 specifications. Use of eye wear which does not comply with ANSI Z87.1 specifications could result in severe injury from breakage of eye protection.

2.Wear proper apparel. No loose clothing or jewelry which can get caught in moving parts. Rubber soled footwear is recommended for best footing.

3.Do not overreach. Failure to maintain proper working position can cause you to fall into the machine or cause your clothing to get caught — pulling you into the machine.

4.Keep guards in place and in proper working order. Do not operate the machine with guards removed.

5.Avoid dangerous working environments. Do not use stationary machine tools in wet or damp locations. Keep work areas clean and well lit.

6.Avoid accidental starts by being sure the start switch is “OFF” before plugging in the machine.

7.Never leave the machine running while unat- tended. Machine shall be shut off whenever it is not in operation.

8.Disconnect electrical power before servicing. Whenever changing accessories or general maintenance is done on the machine, electrical

power to the machine must be disconnected before work is done.

9.Maintain all machine tools with care. Follow all maintenance instructions for lubricating and the changing of accessories. No attempt shall be made to modify or have makeshift repairs done to the machine. This not only voids the warranty but also renders the machine unsafe.

10.Machinery must be anchored to the floor.

11.Secure work. Use clamps or a vise to hold work, when practical. It is safer than using your hands and it frees both hands to operate the machine.

12.Never brush away chips while the machine is in operation.

13.Keep work area clean. Cluttered areas invite accidents.

14.Remove adjusting keys and wrenches before turning machine on.

15.Use the right tool. Don’t force a tool or attach- ment to do a job it was not designed for.

16.Use only recommended accessories and follow manufacturers instructions pertaining to them.

17.Keep hands in sight and clear of all moving parts and cutting surfaces.

18.All visitors should be kept at a safe distance from the work area. Make workshop completely safe by using padlocks, master switches, or by removing starter keys.

19.Know the tool you are using — its application, limitations, and potential hazards.

5

Image 5
Contents Models 2221VS, 2223VS, 2232AC, 2234AC Inch VS Drill PressPage Table of Contents Specifications General SpecificationsWhen setting up machine Machinery general safety warningsWhen using machine When servicing machineGeneral electrical cautions Safety Instructions for Drill PressesWire sizes Securing the Base IntroductionOperation and Set-up Electrical Connection Raising the Drill Head and TableOperating Controls Manual Speed Control Models 2221VS and 2223VS See FigureInverter Speed Control Models 2232AC and 2234AC See Figure Depth IndicatorReplacement of Drive Belt MaintenanceReplacement of Motor LubricationHead Adjustment Machine AdjustmentsTable Adjustment See Figure Radial Adjustment of Head All ModelsFeeds for Drilling Operating PrecautionsWiring Diagram Models 2221 Wiring Diagram Models 2232AC & 2234AC Troubleshooting Optional Equipment Coolant System InstallationWMH Tool Group Replacement PartsPage Part Number Description Qty Parts Listing Drill Head Manual Speed ControlPage Part Number Description Qty 5513683 Screw, Cap Exploded View Spindle Components All Models Parts Listing Spindle Components All Models Exploded View Table and Base All Models Parts List Table and Base All Models Page Vantage Drive Elgin, IL Phone