Wilton 2221VS manual Machine Adjustments, Head Adjustment, Table Adjustment See Figure

Page 11

Inverter Speed Control -

Models 2232AC and 2234AC

1.Spindle pulley drive: Lubricate spindle splines occasionally with light grease.

2.Quill and column: Lubricate with light film of oil.

3.Lift rack: Lubricate regularly with SAE 20 oil (clean rack with kerosene before applying oil).

4.Variable speed drive:

a.Periodically check oil level in sight gauge on (left side of head) (refer to Figure 6).

b.If level is below centerline of sight gauge, add oil.

c.To add oil, remove oil fill tube cover plate. Pull fill tube out of hole in head cover.

d.Add SAE 20 oil to bring oil level up to the centerline of the sight gauge.

e.Put end of fill tube back through hole in head cover. Install fill tube cover and secure with two screws.

Machine Adjustments

Table Adjustment (See Figure 7)

The table can be raised or lowered to accommodate the height of the workpiece. To raise or lower the table, loosen the table lock using the hand crank. Then use the hand crank to move the table to the desired height. Then lock the table in positon.

Head Adjustment

Oil Fill Tube

Sight Gauge

Figure 6: Oil Level Sight Gauge and Fill Tube

WARNING: CHANGE THE RADIAL POSITION OF THE DRILL HEAD ONLY IF THE DRILL PRESS BASE IS SECURED TO THE FLOOR. SWINGING THE DRILL HEAD WITHOUT THE BASE BEING SECURED TO THE FLOOR WILL CAUSE THE DRILL PRESS TO BECOME UNSTABLE AND TIP OVER RESULTING IN INJURY AND/OR DAMAGE TO THE MACHINE.

Radial Adjustment of Head (All Models)

The radial position of the drill head can be changed to accommodate the drilling of a hole that may be offset from the center of the table. Reposition the drill head as follows:

1.Loosen the two clamping hex nuts using the hex socket wrench provided with the machine.

2.The swing the drill head to the desired position.

3.Tighten the two clamping nuts.

Adjustment of Speed Pickup

(Manual Models 2221AC and 2223AC)

1.Loosen screws securing speed pickup (ref. 56-

1)to bracket (ref. 56-2).

2.Adjust the speed pickup gap to approximately 1/8-inch.

3.Operate drill press to verify that speed readout is

operating correctly.

(Inverter Models 2232AC and 2234AC)

1.Loosen screws securing speed pickup (ref.

68A) to bracket (ref. 70A) on drill head.

2.Adjust the speed pickup gap to approximately 1/8-inch.

3.Operate drill press to verify that speed readout is operating correctly.

Table Clamping Handle

Table Raising

 

 

Square Drives

 

 

Figure 7: Table Adjustment

 

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Models 2221VS, 2223VS, 2232AC, 2234AC Inch VS Drill PressPage Table of Contents Specifications General SpecificationsWhen servicing machine Machinery general safety warningsWhen setting up machine When using machineGeneral electrical cautions Safety Instructions for Drill PressesWire sizes Securing the Base IntroductionOperation and Set-up Manual Speed Control Models 2221VS and 2223VS See Figure Raising the Drill Head and TableElectrical Connection Operating ControlsInverter Speed Control Models 2232AC and 2234AC See Figure Depth IndicatorLubrication MaintenanceReplacement of Drive Belt Replacement of MotorRadial Adjustment of Head All Models Machine AdjustmentsHead Adjustment Table Adjustment See FigureFeeds for Drilling Operating PrecautionsWiring Diagram Models 2221 Wiring Diagram Models 2232AC & 2234AC Troubleshooting Optional Equipment Coolant System InstallationWMH Tool Group Replacement PartsPage Part Number Description Qty Parts Listing Drill Head Manual Speed ControlPage Part Number Description Qty 5513683 Screw, Cap Exploded View Spindle Components All Models Parts Listing Spindle Components All Models Exploded View Table and Base All Models Parts List Table and Base All Models Page Vantage Drive Elgin, IL Phone
Top Page Image Contents