TECHNICAL DATA | AG | AG |
Rated input | 750 W | 750 W |
Max. | 10000 | 10000 |
Grinding disk diameter | 10015 mm | 125 mm |
Thread of work spindle | M 104 | M 14 |
Weight without cable | 1,8 kg | 1,8 kg |
Noise/Vibration Information |
|
|
Measured values determined according to EN 60745.Typically, |
|
|
the |
|
|
tool are: | ...87,182 dB(A) | 87,1 dB(A) |
Sound pressure level (K=3dB(A)) | ||
Sound power level (K=3dB(A)) | ...98,193 dB(A) | 98,1 dB(A) |
Wear ear protection! |
|
|
Total vibration values (vector sum in the three axes) |
|
|
determined according to EN 60745: | ....................... | 6,8 m/s2 |
Surface grinding: vibration emission value ah | 6,8 m/s2 | |
Uncertainty K = | 1,5 m/s2 | 1,5 m/s2 |
Disk sanding vibration emission value ah | 3,5 m/s2 | 3,5 m/s2 |
Uncertainty K = | 1,5 m/s2 | 1,5 m/s2 |
For other applications, e.g. Abrasive
Wire Brushing other vibration values could occure.
WARNING
The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 60745 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may signi¿cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signi¿cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.
WARNING! Read all safety warnings and all instructions, including those given in the accompanying brochure. Failure to follow the warnings and instructions may result in electric shock, ¿re and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Safety Warnings Common for Grinding, Sanding, Wire Safety Warnings Common for Grinding, Sanding, Wire Brushing or Abrasive
Brushing Operations:
a) This power tool is intended to function as a grinder, sander,a) This powerwire brush,tool
b) Operations as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.
c) Do not use accessories which are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.
d) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and Ày apart.
e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
f) The arbour size of wheels, flanges, backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each use inspect the accessory such as abrasive wheels for chips
and cracks, backing pad for cracks, tear or excess wear, wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum
h)Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and shop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping Àying debris generated by various operations. The dust mask or respirator must be capable of ¿ltrating particles generated by your operation. Prolonged exposure to high intensity noise may cause hearing loss.
i)Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a broken accessory may Ày away and cause injury beyond immediate area of operation.
j)Hold power tool by insulated gripping surfaces only, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a „live“ wire may make exposed metal parts of the power tool „live“ and shock the operator.
k)Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
l)Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.
m)Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.
n)Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the housing and excessive