Lincoln Electric 11521 service manual Safety Precautions, Uncrating the Power MIG 215XT, Location

Page 11

A-3

INSTALLATION

A-3

 

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Section TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Return to Master TOC

Read entire installation section before starting installation.

SAFETY PRECAUTIONS

WARNING

ELECTRIC SHOCK can kill.

•Only qualified personnel should perform this installation.

•Only personnel that have read and understood the POWER MIG® 215XT Operating Manual should install and operate this equipment.

•Machine must be grounded per any national, local or other applicable electrical codes.

•The Power MIG® power switch is to be in the OFF position when installing work cable and gun and when connecting other equip- ment.

UNCRATING THE POWER MIG® 215XT

Cut banding and lift off cardboard carton. Cut banding holding the machine to the skid. Remove foam and corrugated packing material. Untape accessories from Gas Bottle Platform. Unscrew the two wood screws (at the Gas Bottle Platform) holding the machine to the skid. Roll the machine off the skid assembly.

LOCATION

Locate the welder in a dry location where there is free circulation of clean air into the louvers in the back and out the front. A location that minimizes the amount of smoke and dirt drawn into the rear louvers reduces the chance of dirt accumulation that can block air pas- sages and cause overheating.

INPUT POWER, GROUNDING AND CONNECTION DIAGRAMS

WARNING

ELECTRIC SHOCK can kill.

•Do not touch electrically live parts such as output terminals or internal wiring.

•All input power must be electrically dis- connected before proceeding.

1.Before starting the installation, check with the local power company if there is any question about whether your power supply is adequate for the volt- age, amperes, phase, and frequency specified on the welder nameplate. Also be sure the planned installation will meet the U.S. National Electrical Code and local code requirements. This welder may be operated from a single phase line or from one phase of a two or three phase line.

2.Models that have multiple input voltages specified on the nameplate (e.g. 208/230) are shipped con- nected for the highest voltage. If the welder is to be operated on lower voltage, it must be reconnected according to the instructions in Figure A.1 for dual voltage machines.

WARNING

Make certain that the input power is electrically disconnected before removing the screw on the reconnect panel access cover.

------------------------------------------------------------------------

Power MIG® 215XT

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Power MIG 215XT Power MIG 215XT SafetyElectric Shock can kill ARC Rays can burn Iii Welding CuttingFor Electrically Sûreté Pour Soudage a L’Arc Précautions DE SûretéSafety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Power MIG 215XT InstallationLocation Safety PrecautionsUncrating the Power MIG 215XT Input POWER, Grounding and Connection DiagramsOutput Polarity Connections Cylinder may explode if damaged GUN and Cable InstallationAUXILIARY POWER RECEPTACLES Shielding GASPower MIG 215XT Table of Contents Operation Section Wear eye, ear and body protec- tion OPERATIONB-2Operation Wire Reel Loading READI-REELS, Spools or Coils Wire Drive RollWire Size Conversion Parts Procedure for Changing Drive AND IDLE Roll SetsChanging the Gun Receiver Bushing Electric Shock can kill Feeding Wire ElectrodeWhen triggering, the electrode To Start the WelderReturn to Return to Section TOC Making a WeldInput Line Voltage Variations Avoiding Wire Feeding ProblemsWire Feed Overload Protection FAN ControlPower MIG 215XT Table of Contents Accessories Section Accessories Magnum 250LX Push Pull Adapter K2705-1 Magnum 250LX PUSH-PULL GUN and Push Pull AdapterMake a Weld with the Magnum 250LX PUSH-PULL GUN Magnum 250LX Push Pull Gun K2704-1Accessories Table of Contents Maintenance Section Maintenance Table D.1 Liner Removal and REPLACE- MentEnglish Metric Description Size GUN Handle DisassemblyFigure D.2 Major Component Locations Power MIG 215XT 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Figure E.2 Input Power CircuitOutput RECTIFICATION, Contactor Control Board Figure E.2 Optional Circuits Protective Devices and Circuits Power MIG 215XT 1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide Troubleshooting and RepairPC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Your body These capacitors is toxicAvoid contact with any portion Function Problems Tachometer Feedback Test Body Welding ProblemsMake certain the shielding gas is Test Description Main Transformer TestX4 X5 ON/OFF Power Switch will be hot during these testsX10 Main Transformer Test Wire Drive Motor and Tachometer Feedback Test J11 Wire Drive Motor and Tachometer Feedback Test J11 Output Bridge Rectifier Test Negative Lead Contactor Test Contactor Test Machine Loaded to 200 Amps AT 22 VDC Typical Output Voltage Waveform Machine Loaded MAX TAP GNormal Open Circuit Voltage Waveform MAX TAP G Machine Loaded to 180 Amps AT 16 VDC Troubleshooting and Repair Control Board Removal and Replacement Procedure Depress Locking TAB on Mounting PIN Wire Drive Motor Removal and Replacement Procedure Wire Drive Bolt Gas Hose TOC Test Description Output Diode Bridge Rectifier Output Diode Bridge RectifierMounting Bracket Mounting Bolts Rectifier Power MIG 215XT Output Capacitors Removal and Replacement Procedure Lower Right Case Wraparound Cover Capacitor Bank Assembly Lead Mounting Bolts Nuts & Lock washers Places Power MIG 215XT Main Transformer Removal and Replacement Procedure Main Transformer Mounting Bolts Replacement X4 X5 Lead Power MIG 215XT FAN Blade / Motor Removal and Replacement Procedure Rear Output Contactor Removal and Replacement Procedure Output Contactor Mounting Bolts Retest After Repair Table of Contents Diagram Section POWEr miG 215XT Power MIG 215XT 208/220/230V for CodeSchEmaTic cOmplETE machiNE l12308-1 pG1 SchEmaTic cOmplETE machiNE l12308-1 pG2 Psoc 1pF Calibrate

11521 specifications

The Lincoln Electric 11521 is a highly regarded choice among welders and metal fabricators, known for its reliability and efficiency. This portable MIG welder excels in delivering professional-grade results, making it suitable for both beginners and experienced welders. One of the standout features of the Lincoln Electric 11521 is its user-friendly design, which facilitates ease of use and enhances the overall welding experience.

Equipped with a powerful 180 amp output, the Lincoln Electric 11521 is capable of tackling a wide range of welding applications. It operates on a standard 230-volt outlet, allowing users to work on various materials, including mild steel, stainless steel, and aluminum, with thicknesses up to 5/16 inch. This versatility is crucial for those who handle different types of projects, from automotive repairs to home improvement tasks.

The welder employs a spool gun for welding aluminum, ensuring a smooth and efficient feeding of the wire. This technology mitigates the problems commonly associated with feeding aluminum wire through a regular gun, providing a seamless experience. Additionally, the Lincoln Electric 11521 features an adjustable welding speed and voltage, enabling users to fine-tune their settings to match the specific requirements of each project. This adaptability leads to better penetration, bead shape, and overall weld quality.

Another important aspect of the Lincoln Electric 11521 is its durability. Constructed with high-quality materials, this welder is designed for tough jobs and can withstand the wear and tear associated with heavy use. The unit's compact size and lightweight design further enhance its practicality, making it easy to transport between job sites or store when not in use.

Safety is a crucial element in welding, and the Lincoln Electric 11521 does not compromise on this aspect. It features a thermal overload protection system, which prevents damage to the machine by shutting it down in case of overheating. The welder also includes a gas-saving mode that intelligently reduces the gas flow during idle times, maximizing efficiency.

In summary, the Lincoln Electric 11521 is a versatile and reliable MIG welder that caters to a wide range of welding needs. With its powerful output, user-friendly features, advanced technologies, and robust safety mechanisms, it is an excellent investment for professionals and hobbyists alike looking to achieve high-quality welds with ease.
Top Page Image Contents