Lincoln Electric 11521 service manual Making a Weld, Return to Return to Section TOC

Page 20
Figure B.2b

B-6

OPERATION

B-6

 

Return to Section TOC

Return to Section TOC

Section TOC

Return to Master TOC

Return to Master TOC

Master TOC

5.Loosen the socket head cap screw that holds the connector bar against the gun bushing.

Important: Do not attempt to completely remove the socket head cap screw.

6.Remove the outer wire guide, and push the gun bushing out of the wire drive. Because of the pre- cision fit, light tapping may be required to remove the gun bushing.

7.Disconnect the shielding gas hose from the gun bushing, if required.

8.Connect the shielding gas hose to the new gun bushing, if required.

9.Rotate the gun bushing until the thumb screw hole aligns with the thumb screw hole in the feed plate. Slide the gun receiver bushing into the wire drive and verify the thumb screw holes are aligned.

10.Tighten the socket head cap screw.

11.Insert the welding gun into the gun bushing and tighten the thumb screw.

MAKING A WELD

1.Check that the electrode polarity is correct for the process being used, then turn the power switch ON.

2.Set desired arc voltage tap and wire speed for the

particular electrode wire, material type and thick- ness, and gas (for MIG and Outershield®) being used. Use the Application Chart on the door inside the wire compartment as a quick reference for some common welding procedures.

3.Press the trigger to feed the wire electrode through the gun and cable. For solid wire cut the electrode

within approximately 3/8" (10 mm) of the end of the contact tip [3/4" (20 mm) for Outershield®].

4.When welding with gas, turn on the gas supply and set the required flow rate (typically 25-35 CFH; 12- 16 liters/min).

5.Connect work cable to metal to be welded. Work clamp must make good electrical contact to the work. The work must also be grounded as stated in “Arc Welding Safety Precautions”.

WARNING

•When using an open arc process, it is necessary to use correct eye,

head, and body protection.

-----------------------------------------------------------------------

6.Position electrode over joint. End of electrode may be lightly touching the work.

7.Lower welding helmet, close gun trigger, and begin welding. Hold the gun so the contact tip to work dis-

tance is about 3/8" (10 mm) [3/4" (20 mm) for Outershield®].

8.To stop welding, release the gun trigger and then pull the gun away from the work after the arc goes out.

THUMB SCREW

GUN RECEIVER BUSHING

OUTER WIRE GUIDE

CONNECTOR BLOCK

SOCKET HEAD

CAP SCREW

LOOSEN TIGHTEN

Power MIG® 215XT

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Power MIG 215XT Safety Power MIG 215XTElectric Shock can kill ARC Rays can burn Iii Welding CuttingFor Electrically Précautions DE Sûreté Sûreté Pour Soudage a L’ArcSafety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Installation Technical Specifications Power MIG 215XTSafety Precautions Uncrating the Power MIG 215XTInput POWER, Grounding and Connection Diagrams LocationOutput Polarity Connections GUN and Cable Installation AUXILIARY POWER RECEPTACLESShielding GAS Cylinder may explode if damagedPower MIG 215XT Table of Contents Operation Section OPERATIONB-2 Wear eye, ear and body protec- tionOperation Wire Drive Roll Wire Size Conversion PartsProcedure for Changing Drive AND IDLE Roll Sets Wire Reel Loading READI-REELS, Spools or CoilsFeeding Wire Electrode When triggering, the electrodeTo Start the Welder Changing the Gun Receiver Bushing Electric Shock can killMaking a Weld Return to Return to Section TOCAvoiding Wire Feeding Problems Wire Feed Overload ProtectionFAN Control Input Line Voltage VariationsPower MIG 215XT Table of Contents Accessories Section Accessories Magnum 250LX PUSH-PULL GUN and Push Pull Adapter Make a Weld with the Magnum 250LX PUSH-PULL GUNMagnum 250LX Push Pull Gun K2704-1 Magnum 250LX Push Pull Adapter K2705-1Accessories Table of Contents Maintenance Section Maintenance Liner Removal and REPLACE- Ment Table D.1GUN Handle Disassembly English Metric Description SizeFigure D.2 Major Component Locations Power MIG 215XT 1TABLE of CONTENTS-THEORY of Operation Section E-1 Figure E.2 Input Power Circuit Theory of OperationOutput RECTIFICATION, Contactor Control Board Figure E.2 Optional Circuits Protective Devices and Circuits Power MIG 215XT 1TABLE of Contents Troubleshooting and Repair F-1 Troubleshooting and Repair HOW to USE Troubleshooting GuidePC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Your body These capacitors is toxicAvoid contact with any portion Function Problems Tachometer Feedback Test Welding Problems BodyMake certain the shielding gas is Main Transformer Test Test DescriptionON/OFF Power Switch will be hot during these tests X4 X5X10 Main Transformer Test Wire Drive Motor and Tachometer Feedback Test J11 Wire Drive Motor and Tachometer Feedback Test J11 Output Bridge Rectifier Test Negative Lead Contactor Test Contactor Test Typical Output Voltage Waveform Machine Loaded MAX TAP G Machine Loaded to 200 Amps AT 22 VDCNormal Open Circuit Voltage Waveform MAX TAP G Machine Loaded to 180 Amps AT 16 VDC Troubleshooting and Repair Control Board Removal and Replacement Procedure Depress Locking TAB on Mounting PIN Wire Drive Motor Removal and Replacement Procedure Wire Drive Bolt Gas Hose TOC Test Description Output Diode Bridge Rectifier Output Diode Bridge RectifierMounting Bracket Mounting Bolts Rectifier Power MIG 215XT Output Capacitors Removal and Replacement Procedure Lower Right Case Wraparound Cover Capacitor Bank Assembly Lead Mounting Bolts Nuts & Lock washers Places Power MIG 215XT Main Transformer Removal and Replacement Procedure Main Transformer Mounting Bolts Replacement X4 X5 Lead Power MIG 215XT FAN Blade / Motor Removal and Replacement Procedure Rear Output Contactor Removal and Replacement Procedure Output Contactor Mounting Bolts Retest After Repair Table of Contents Diagram Section Power MIG 215XT 208/220/230V for Code POWEr miG 215XTSchEmaTic cOmplETE machiNE l12308-1 pG1 SchEmaTic cOmplETE machiNE l12308-1 pG2 Psoc 1pF Calibrate

11521 specifications

The Lincoln Electric 11521 is a highly regarded choice among welders and metal fabricators, known for its reliability and efficiency. This portable MIG welder excels in delivering professional-grade results, making it suitable for both beginners and experienced welders. One of the standout features of the Lincoln Electric 11521 is its user-friendly design, which facilitates ease of use and enhances the overall welding experience.

Equipped with a powerful 180 amp output, the Lincoln Electric 11521 is capable of tackling a wide range of welding applications. It operates on a standard 230-volt outlet, allowing users to work on various materials, including mild steel, stainless steel, and aluminum, with thicknesses up to 5/16 inch. This versatility is crucial for those who handle different types of projects, from automotive repairs to home improvement tasks.

The welder employs a spool gun for welding aluminum, ensuring a smooth and efficient feeding of the wire. This technology mitigates the problems commonly associated with feeding aluminum wire through a regular gun, providing a seamless experience. Additionally, the Lincoln Electric 11521 features an adjustable welding speed and voltage, enabling users to fine-tune their settings to match the specific requirements of each project. This adaptability leads to better penetration, bead shape, and overall weld quality.

Another important aspect of the Lincoln Electric 11521 is its durability. Constructed with high-quality materials, this welder is designed for tough jobs and can withstand the wear and tear associated with heavy use. The unit's compact size and lightweight design further enhance its practicality, making it easy to transport between job sites or store when not in use.

Safety is a crucial element in welding, and the Lincoln Electric 11521 does not compromise on this aspect. It features a thermal overload protection system, which prevents damage to the machine by shutting it down in case of overheating. The welder also includes a gas-saving mode that intelligently reduces the gas flow during idle times, maximizing efficiency.

In summary, the Lincoln Electric 11521 is a versatile and reliable MIG welder that caters to a wide range of welding needs. With its powerful output, user-friendly features, advanced technologies, and robust safety mechanisms, it is an excellent investment for professionals and hobbyists alike looking to achieve high-quality welds with ease.
Top Page Image Contents