Lincoln Electric 11521 Magnum 250LX PUSH-PULL GUN and Push Pull Adapter, See Figure C.1

Page 25
FIGURE C.1

C-3

ACCESSORIES

C-3

 

Return to Section TOC

Return to Section TOC

to Section TOC

Return to Master TOC

Return to Master TOC

to Master TOC

MAGNUM 250LX PUSH-PULL GUN AND PUSH PULL ADAPTER

For heavier duty aluminum applications when use of large 16 pound aluminum spools of wire are desired the follow- ing push pull gun and adapter kit are available.

Magnum 250LX Push Pull Gun (K2704-1)

This pistol grip push pull gun is similar to the Magnum 250LX spool gun except it is designed to feed large spools of wire. The Magnum 250LX push pull features a 25 foot power, gas and control cable. It operates as an assist slave motor pulling the aluminum wire as the Power MIG® drive motor acts as the master push motor.

Magnum 250LX Push Pull Adapter (K2705-1)

This adapter box is designed to drive the Magnum 250LX push pull gun when used on a non push ready Lincoln power source feeder such as the Power MIG® 215XT or 255XT. This box features a 115V cord and plug to power the box, a control cable with receptacle to connect the push pull gun’s control cable to, and a 4-pin connector to connect to the Power MIG® gun trigger receptacle.

Note the Magnum 250LX push pull gun has a wire feed speed adjustment potentiometer. However this poten- tiometer only functions on push-pull ready machines like the Power MIG® 350MP. When the Magnum 250LX is used on a non-push-pull machine with the K2705-1 adapter, the wire feed speed is set on the control panel of the machine.

CONNECTING THE MAGNUM 250LX PUSH-PULL GUN (K2704-1) AND MAGNUM 250LX PUSH-PULL GUN ADAPTER (K2705-1)

See Figure C.1

1.Plug the 115 VAC cable into available 115V AC recep- tacle. The Power MIG® 215XT (K2701-1) furnishes the 15A 115V AC auxiliary supply. The receptacle is located at the back of the machine.

2.Connect the 4-pin connector cable of the Push-Pull Gun Adapter to the 4-pin trigger receptacle located in the front section of the wire drive compartment.

3.Connect the 7-pin connector cable of the Push-Pull Gun to the 7-pin receptacle cable from the adapter.

4.Connect the Push-Pull gas & power pin into the Power MIG® wire feeder brass bushing.

5.Attach a gas hose from the Gas supply to the rear inlet gas fitting on the Power MIG® 215XT

MAKE A WELD WITH THE MAGNUM 250LX PUSH-PULL GUN

1.Power MIG® 215XT

a.Set machine to non spool gun operation.

b.Turn the Power MIG® 215XT input power ON.

c.Adjust the voltage control at the front panel.

d.Adjust the wire speed control on the front panel. Refer to the procedure decal mounted at the inside of the wire feeder compartment cover.

2.Magnum 250LX Push-Pull Gun:

a.Set machine to non spool gun operation.

b.Closing Push-Pull gun trigger starts the Push-Pull gun welding and makes all guns connected to the machine electrically “Hot”.

c.The Push-Pull Adapter will provide power and con- trol to the “Pull” motor of the Push-Pull gun & the Power MIG® 215XT will control its wire drive.

Return

Return to Section TOC

Return

Return to Master TOC

4-PIN

CABLE CONNECTOR

MAGNUM 250LX

PUSH-PULL GUN

7-PIN

CABLE CONNECTORS

ADAPTER

PLUG INTO

AVAILABLE 120VAC

POWER SOURCE

Power MIG® 215XT

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Power MIG 215XT Power MIG 215XT SafetyElectric Shock can kill ARC Rays can burn For Electrically Welding CuttingIii Sûreté Pour Soudage a L’Arc Précautions DE SûretéSafety Methods of Reducing Emissions Mains Supply Master Table of Contents for ALL Sections Table of Contents Installation Section Technical Specifications Power MIG 215XT InstallationUncrating the Power MIG 215XT Safety PrecautionsInput POWER, Grounding and Connection Diagrams LocationOutput Polarity Connections AUXILIARY POWER RECEPTACLES GUN and Cable InstallationShielding GAS Cylinder may explode if damagedPower MIG 215XT Table of Contents Operation Section Wear eye, ear and body protec- tion OPERATIONB-2Operation Wire Size Conversion Parts Wire Drive RollProcedure for Changing Drive AND IDLE Roll Sets Wire Reel Loading READI-REELS, Spools or CoilsWhen triggering, the electrode Feeding Wire ElectrodeTo Start the Welder Changing the Gun Receiver Bushing Electric Shock can killReturn to Return to Section TOC Making a WeldWire Feed Overload Protection Avoiding Wire Feeding ProblemsFAN Control Input Line Voltage VariationsPower MIG 215XT Table of Contents Accessories Section Accessories Make a Weld with the Magnum 250LX PUSH-PULL GUN Magnum 250LX PUSH-PULL GUN and Push Pull AdapterMagnum 250LX Push Pull Gun K2704-1 Magnum 250LX Push Pull Adapter K2705-1Accessories Table of Contents Maintenance Section Maintenance Table D.1 Liner Removal and REPLACE- MentEnglish Metric Description Size GUN Handle DisassemblyFigure D.2 Major Component Locations Power MIG 215XT 1TABLE of CONTENTS-THEORY of Operation Section E-1 Theory of Operation Figure E.2 Input Power CircuitOutput RECTIFICATION, Contactor Control Board Figure E.2 Optional Circuits Protective Devices and Circuits Power MIG 215XT 1TABLE of Contents Troubleshooting and Repair F-1 HOW to USE Troubleshooting Guide Troubleshooting and RepairPC Board Troubleshooting Procedures Perform the Main Transformer Perform the Output Contactor Avoid contact with any portion These capacitors is toxicYour body Function Problems Tachometer Feedback Test Body Welding ProblemsMake certain the shielding gas is Test Description Main Transformer TestX4 X5 ON/OFF Power Switch will be hot during these testsX10 Main Transformer Test Wire Drive Motor and Tachometer Feedback Test J11 Wire Drive Motor and Tachometer Feedback Test J11 Output Bridge Rectifier Test Negative Lead Contactor Test Contactor Test Machine Loaded to 200 Amps AT 22 VDC Typical Output Voltage Waveform Machine Loaded MAX TAP GNormal Open Circuit Voltage Waveform MAX TAP G Machine Loaded to 180 Amps AT 16 VDC Troubleshooting and Repair Control Board Removal and Replacement Procedure Depress Locking TAB on Mounting PIN Wire Drive Motor Removal and Replacement Procedure Wire Drive Bolt Gas Hose TOC Test Description Output Diode Bridge Rectifier Output Diode Bridge RectifierMounting Bracket Mounting Bolts Rectifier Power MIG 215XT Output Capacitors Removal and Replacement Procedure Lower Right Case Wraparound Cover Capacitor Bank Assembly Lead Mounting Bolts Nuts & Lock washers Places Power MIG 215XT Main Transformer Removal and Replacement Procedure Main Transformer Mounting Bolts Replacement X4 X5 Lead Power MIG 215XT FAN Blade / Motor Removal and Replacement Procedure Rear Output Contactor Removal and Replacement Procedure Output Contactor Mounting Bolts Retest After Repair Table of Contents Diagram Section POWEr miG 215XT Power MIG 215XT 208/220/230V for CodeSchEmaTic cOmplETE machiNE l12308-1 pG1 SchEmaTic cOmplETE machiNE l12308-1 pG2 Psoc 1pF Calibrate

11521 specifications

The Lincoln Electric 11521 is a highly regarded choice among welders and metal fabricators, known for its reliability and efficiency. This portable MIG welder excels in delivering professional-grade results, making it suitable for both beginners and experienced welders. One of the standout features of the Lincoln Electric 11521 is its user-friendly design, which facilitates ease of use and enhances the overall welding experience.

Equipped with a powerful 180 amp output, the Lincoln Electric 11521 is capable of tackling a wide range of welding applications. It operates on a standard 230-volt outlet, allowing users to work on various materials, including mild steel, stainless steel, and aluminum, with thicknesses up to 5/16 inch. This versatility is crucial for those who handle different types of projects, from automotive repairs to home improvement tasks.

The welder employs a spool gun for welding aluminum, ensuring a smooth and efficient feeding of the wire. This technology mitigates the problems commonly associated with feeding aluminum wire through a regular gun, providing a seamless experience. Additionally, the Lincoln Electric 11521 features an adjustable welding speed and voltage, enabling users to fine-tune their settings to match the specific requirements of each project. This adaptability leads to better penetration, bead shape, and overall weld quality.

Another important aspect of the Lincoln Electric 11521 is its durability. Constructed with high-quality materials, this welder is designed for tough jobs and can withstand the wear and tear associated with heavy use. The unit's compact size and lightweight design further enhance its practicality, making it easy to transport between job sites or store when not in use.

Safety is a crucial element in welding, and the Lincoln Electric 11521 does not compromise on this aspect. It features a thermal overload protection system, which prevents damage to the machine by shutting it down in case of overheating. The welder also includes a gas-saving mode that intelligently reduces the gas flow during idle times, maximizing efficiency.

In summary, the Lincoln Electric 11521 is a versatile and reliable MIG welder that caters to a wide range of welding needs. With its powerful output, user-friendly features, advanced technologies, and robust safety mechanisms, it is an excellent investment for professionals and hobbyists alike looking to achieve high-quality welds with ease.
Top Page Image Contents