Wagner SprayTech 9140S, 9210 Accessories, Daily Maintenance, Extended Maintenance

Page 13

MAINTENANCE

DAILY MAINTENANCE

The only daily maintenance necessary is thorough cleaning. Follow the cleaning procedures in this manual.

EXTENDED MAINTENANCE

Some pump parts eventually wear out from use and must be replaced. The following list indicates the available repair kits for the parts replaced by each kit. However, pump performance is the only reliable indicator of when to replace wear parts. Refer to the Troubleshooting section for more information on when to use these kits.

Kit Part #

Description

0512228

Fluid Section Seal Kit (9140, 9140S, 9150)

0512222

Valve Replacement Kit (9140, 9140S, 9150)

0512229

Fluid Section Seal Kit (9170, 9190, 9210)

0512224

Valve Replacement Kit (9170, 9190, 9210)

CLEANING THE INLET VALVE

Cleaning or servicing the inlet valve may be required if the unit has priming problems. This may be caused by improper cleaning and/or storage.

1. Unscrew the inlet valve assembly from the unit with a crescent wrench.

2. Unscrew the inlet nut

Housing

 

using a 3/8 inch allen

Inlet valve

 

wrench.

Inlet nut

assembly

 

3.Remove excess paint or

rust from the ball and seat or replace with new parts from kit P/N 0512222 (9140, 9140S, 9150) or P/N 0512224 (9170, 9190, 9210). You may also have to clean excess paint inside the housing.

4.Inspect the inlet O-ringon the inlet valve. Clean or replace, and lubricate with a light household oil.

4.Reassemble ball, carbide seat, and O-rings in the order shown below into the inlet valve.

9140S9140,Modelsand 9150 assemblyvalveinlet

Inlet O-ring

9190,9170,Modelsand 9120

assemblyvalveinlet

Inlet valve

 

 

 

 

Ball

 

 

 

O-ring

 

 

 

Carbide seat

 

 

 

O-ring

 

 

 

Inlet nut

 

 

5.Install inlet nut back into inlet valve. Torque to 12 ± 2 ft/lbs if you have torque wrench.

6.Make sure the inlet valve O-ringis installed on the inlet valve, then install entire inlet valve assembly back into unit. Tighten with an adjustable wrench.

ACCESSORIES

Part #

Description

 

0154908

Separating Oil

 

0154830

Hose, Whip End, 5’ x 3/16”

0270192

Hose, Wireless, 25’ x 1/4"

0291000

Hose, Wireless, 50’ x 1/4"

0279667

Hose Connector, 1/4” x 1/4”

0088154

Pressure Gauge

 

0508910

Tip Extension, 12”

 

0508914

Tip Extension, 24”

 

0152001

Power Roller Gun Attachment

0155206

9" Roller Cover, 3/8”

Nap

0152307

9" Roller Cover, 1/2”

Nap

0155208

9" Roller Cover, 3/4”

Nap

0152310

9" Roller Cover, 1-1/4” Nap

0512181

GX-08 Four Finger Metal Airless Spray Gun

0512180

GX-07 Two Finger Metal Airless Spray Gun

0512179

GX-06 Two Finger Plastic Airless Spray Gun

0512182

GX-10 Two Finger Metal Airless Spray Gun w/Swivel

0501010

Guard Assembly, F-Thread

0512508

Guard Assembly, G-Thread

0279974

3 Foot Pole Extension w/Swivel

0279976

6 Foot Pole Extension w/Swivel

0512134

180 Degree Swivel

 

0508931

F- to G-Thread Adapter

0154832

Suction Set Filter (2 Pack)

0512500

411 Trade Spray Tip

 

0512501

413 Trade Spray Tip

 

0512502

415 Trade Spray Tip

 

0512503

417 Trade Spray Tip

 

0501419

419 Trade Spray Tip

 

0512504

515 Trade Spray Tip

 

0512505

517 Trade Spray Tip

 

0512506

519 Trade Spray Tip

 

0093930

Anti-Seize Compound

0156113

TR-10 Telescoping Roller, 9", 3/8" Nap

0089959

Yellow Gun Filter

 

0089958

White Gun Filter

 

0279109

Pump Saver Plus Protector

© 2003 Wagner Spray Tech - All rights reserved.

13 Customer Service: 800-880-0993

English

 

 

 

Image 13
Contents Specifications Table of ContentsHigh Performance Airless Sprayer Safety Information Read ALL Safety Grounding Instructions Important Electrical InformationComponents Components and DescriptionControls and Functions SETUP--ASSEMBLING the Sprayer Before YOU Begin Pressure Relief ProcedurePlugging in the Sprayer Before YOU Prime the SprayerYour hose is now purged and primed. You are ready to paint Purging & PrimingPractice SprayingSpraying Technique Cleaning the Spray GUN Filter Spraying TroubleshootingCleaning the Suction SET Screen Unclogging the Spray TIPCleaning the Suction SET CleanupMove on to Cleaning the Suction Set Move on to Cleaning the Spray Gun, nextCleaning the Spray GUN Filter and TIP Assembly Preparing the Sprayer for LONG- Term Storage StorageShutdown StartupAccessories MaintenanceDaily Maintenance Extended MaintenanceDisassembly of the Fluid Section Fluid Section Seal Replacement InstructionsAssembly of the Fluid Section Problem TroubleshootingSuction SET Dispositif ’ASPIRATION Juego DE Succió N Parts List Liste DE PIÈ CES Lista DE PiezasArticulo Article N de piè ce Description Quantity0296343 02962910347706 0296262Article N de piè ce Description Quantité Articulo Pieza# Descripció n CantidadFernbrook Lane Wagner Spray Tech CorporationMinneapolis, Minnesota Telephone

9140, 9140S, 9210 specifications

Wagner SprayTech is a renowned name in the field of paint sprayers, offering innovative solutions for both professionals and DIY enthusiasts. Among its impressive lineup, the Wagner SprayTech 9210, 9140S, and 9140 models stand out due to their advanced features and technologies, making paint application more efficient and manageable.

The Wagner SprayTech 9210 is designed for versatility and efficiency. It boasts a high-performance motor, allowing for consistent spray patterns and even coverage. This model features the Flexio technology, which utilizes two independent paint flow controls for superior control over paint flow rate and air pressure. This ensures minimal overspray and allows for precise application on a variety of surfaces, from walls to furniture.

The 9140S model builds on the performance of the 9210, emphasizing ease of use. One of the key features is the adjustable material flow dial, enabling users to tailor the paint output according to their specific needs. It also incorporates a unique iSpray nozzle, which provides a wide spray pattern and is perfect for large surfaces. Additionally, the 9140S is engineered for cleaning convenience, with a quick-release system that allows for fast disassembly and thorough cleaning, promoting longevity and durability.

The 9140 model is a compact and lightweight option ideal for smaller projects or tight spaces. It offers a simplified design without sacrificing performance. It comes equipped with a powerful turbine that delivers a fine finish, whether users are applying stains, sealers, or paints. The adjustable air cap allows for horizontal or vertical patterns, adding to its versatility.

All three models are designed with user-friendly features, including ergonomic handles and easy-to-fill tanks. They are suitable for a range of materials, making them ideal for various painting projects. Whether you're a professional painter or a weekend DIY warrior, Wagner SprayTech’s 9210, 9140S, and 9140 provide the technology and design to achieve a professional-quality finish with minimal effort. With their combination of innovative technologies, adjustable features, and ease of use, these sprayers are an excellent choice for anyone looking to enhance their painting experience.