Friedrich ZQ10 A10B manual

Page 10

NOTES

—Replacement of the refrigeration cycle.

1.When replacing the refrigeration cycle, be sure to Discharge the refrigerant system using a FreonTM recovery System.

If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the FreonTM. Leave the valve in place after servicing the system.

2.After discharging the unit completely, remove the desired component, and unbraze the pinch-off tubes.

3.Solder service valves into the pinch-off tube ports, leaving the valves open.

4.Solder the pinch-off tubes with Service valves.

5.Evacuate as follows.

1)Connect the vacuum pump, as illustrated figure 16A.

2)Start the vacuum pump, slowly open manifold valves A and B with two full turns counterclockwise and leave the valves open. The vacuum pump is now pulling through valves A and B up to valve C by means of the manifold and entire system.

CAUTION

If high vacuum equipment is used, just crack valves A and B for a few minutes, then open slowly with the two full turns counterclockwise. This will keep oil from foaming and being drawn into the vacuum pump.

3)Operate the vacuum pump for 20 to 30 minutes, until 600 microns of vaccum is obtained. Close valves A and B, and observe vacuum gauge for a few minutes. A rise in pressure would indicate a possible leak or moisture remaining in the system. With valves A and B closed, stop the vacuum pump.

4)Remove the hose from the vacuum pump and place it on the charging cylinder. See figure 16B.

Open valve C.

Discharge the line at the manifold connection.

5)The system is now ready for final charging.

6.Recharge as follows :

1)Refrigeration cycle systems are charged from the High-side. If the total charge cannot be put in the High-side, the balance will be put in the suction line through the access valve which you installed as the system was opened.

2)Connect the charging cylinder as shown in figure 16B.

With valve C open, discharge the hose at the manifold connection.

3)Open valve A and allow the proper charge to enter the system. Valve B is still closed.

4)If more charge is required, the high-side will not take it. Close valve A.

5)With the unit running, open valve B and add the balance of the charge.

a.Do not add the liquid refrigerant to the Low- side.

b.Watch the Low-side gauge; allow pressure to rise to 30 lbs.

c.Turn off valve B and allow pressure to drop.

d.Repeat steps b. and c. until the balance of the charge is in the system.

6)When satisfied the unit is operating correctly, use the pinch-off tool with the unit still running and clamp on to the pinch-off tube. Using a tube cutter, cut the pinch-off tube about 2 inches from the pinch-off tool. Use sil-fos solder and solder pinch-off tube closed. Turn off the unit, allow it to set for a while, and then test the leakage of the pinch-off connection.

— 10—

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Room Air Conditioner Service and Parts Manual ZStarTM Contents PrefaceZQ10A10B SpecificationsModels ItemsControl Locations FeaturesControl only Model Front Grille Disassembly InstructionsMechanical Parts CabinetAIR Guide and Blower AIR Handling PartsFAN and Shroud Compressor Electrical PartsOverload Protector CapacitorRotary Switch Power CordThermostat Evaporator Refrigerating CycleCondenser Capillary TubePage Pulling Vacuum Installation Hardware InstallationSelect the Best Location Wood Pieces Window RequirementsStorm Window Requirements Width Minimum 1 1/238mmPreparing the Unit for Installation Before InstallationInstall the Case in the Window Install the AIR Conditioner in the Case To Reverse the Grille OpeningTroubleshooting Guide Outside DimensionsPiping System Evaporator CoilTroubleshooting Guide Ineffective CoolingFails to Start Name Plate Rating Minimum Maximum Room AIR Conditioner Voltage LimitsComplaint Cause Remedy Complaint Cause Remedy Complaint Cause Remedy Description QTY Schematic DiagramCircuit Diagram PER SETExploded View Replacement Parts List Model ZQ10A10BControl BOX Assy Use Factory Certified Parts

ZQ10 A10B specifications

The Friedrich ZQ10 A10B is a prominent industrial solution designed for efficient and reliable air conditioning and heating applications. Engineered with advanced technologies, this unit stands out in its category due to its versatility, energy efficiency, and user-friendly features.

At the heart of the ZQ10 A10B is its robust refrigeration cycle, utilizing an environmentally friendly refrigerant that aligns with modern sustainability practices. This refrigerant not only minimizes the environmental impact but also ensures optimal performance across varying temperature conditions. The system's high cooling and heating capacities make it suitable for both residential and commercial settings.

One of the key characteristics of the ZQ10 A10B is its smart inverter technology. This innovation allows the unit to adjust its power consumption based on the current load requirements, providing significant energy savings over traditional fixed-speed systems. By operating at variable speeds, the system enhances comfort levels while reducing operational costs, making it an attractive option for budget-conscious consumers.

Moreover, the ZQ10 A10B integrates a sophisticated microprocessor control system, enabling precise temperature regulation and simplified user interaction. This intuitive control interface allows users to easily program settings and monitor system performance, leading to a higher degree of comfort and convenience.

The unit is also designed for quiet operation, featuring a sound-dampening casing that minimizes noise levels. This is particularly advantageous in residential environments where noise disturbance can be a significant concern. Additionally, the ZQ10 A10B is equipped with advanced filtration technologies that improve indoor air quality by effectively capturing dust, allergens, and other airborne pollutants, ensuring a healthier living space.

Durability is another hallmark of the Friedrich ZQ10 A10B. Built with high-quality materials, the unit is resistant to corrosion and wear, promising longevity and consistent performance throughout its lifecycle. This resilience makes it a reliable choice in harsh environmental conditions.

Integrated with smart connectivity features, users can control the ZQ10 A10B remotely via smartphone applications, allowing for greater flexibility and ease of use. This integration aligns with the growing trend of smart home technology, appealing to tech-savvy consumers looking for greater control over their heating and cooling systems.

In conclusion, the Friedrich ZQ10 A10B emerges as a leading solution in the HVAC market, combining innovative technology with user-focused design. Its energy efficiency, durability, and advanced features make it a smart investment for anyone looking to enhance their home or business climate control systems while keeping an eye on environmental impact.
Top Page Image Contents