Friedrich ZQ10 A10B manual Electrical Parts, Overload Protector, Compressor, Capacitor

Page 7

2.3 ELECTRICAL PARTS

2.3.1 OVERLOAD PROTECTOR

1. Remove the cabinet. (Refer to section 2.1.2)

2. Remove the nut which fastens the terminal cover.

3. Remove the terminal cover. (See Figure 7)

4. Remove all the leads from the overload protector.

5. Remove the overload protector.

6. Re-install the component by referring to the removal procedure, above.

Figure 7

2.3.2 COMPRESSOR

1.Remove the cabinet. (Refer to section 2.1.2)

2.Discharge the refrigerant system using a FreonTM

Recovery System.

If there is no valve to attach the recovery system, install one (such as a WATCO A-1) before venting the FreonTM. Leave the valve in place after servicing the system.

3. Remove the overload protector. (Refer to section 2.3.1)

4. After purging the unit completely, unbraze the suction and discharge tubes at the compressor

connections.

5. Remove the 3 nuts and the 3 washers whichFigure 8 fasten the compressor.

6.Remove the compressor. (See Figure 8)

7.Re-install the components by referring to the removal procedure, above.

2.3.3 CAPACITOR

1. Remove the control box. (Refer to section 2.1.3)

2. Remove the knobs and the screw which fasten control panel from control box.

3. Remove the screw which is located in the front.

4. Open the bottom side of control box.

5. Remove the screw and the clamp which fasten the capacitor.

6. Disconnect all the leads of capacitor terminals.

7. Re-install the components by referring to the removal procedure, above. (See Figure 9)

Figure 9

— 7—

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Room Air Conditioner Service and Parts Manual ZStarTM Preface ContentsItems SpecificationsModels ZQ10A10BControl Locations FeaturesControl only Model Cabinet Disassembly InstructionsMechanical Parts Front GrilleAIR Guide and Blower AIR Handling PartsFAN and Shroud Capacitor Electrical PartsOverload Protector CompressorRotary Switch Power CordThermostat Capillary Tube Refrigerating CycleCondenser EvaporatorPage Pulling Vacuum Installation Hardware InstallationSelect the Best Location Width Minimum 1 1/238mm Window RequirementsStorm Window Requirements Wood PiecesBefore Installation Preparing the Unit for InstallationInstall the Case in the Window To Reverse the Grille Opening Install the AIR Conditioner in the CaseOutside Dimensions Troubleshooting GuideEvaporator Coil Piping SystemIneffective Cooling Troubleshooting GuideFails to Start Name Plate Rating Minimum Maximum Room AIR Conditioner Voltage LimitsComplaint Cause Remedy Complaint Cause Remedy Complaint Cause Remedy PER SET Schematic DiagramCircuit Diagram Description QTYExploded View Model ZQ10A10B Replacement Parts ListControl BOX Assy Use Factory Certified Parts

ZQ10 A10B specifications

The Friedrich ZQ10 A10B is a prominent industrial solution designed for efficient and reliable air conditioning and heating applications. Engineered with advanced technologies, this unit stands out in its category due to its versatility, energy efficiency, and user-friendly features.

At the heart of the ZQ10 A10B is its robust refrigeration cycle, utilizing an environmentally friendly refrigerant that aligns with modern sustainability practices. This refrigerant not only minimizes the environmental impact but also ensures optimal performance across varying temperature conditions. The system's high cooling and heating capacities make it suitable for both residential and commercial settings.

One of the key characteristics of the ZQ10 A10B is its smart inverter technology. This innovation allows the unit to adjust its power consumption based on the current load requirements, providing significant energy savings over traditional fixed-speed systems. By operating at variable speeds, the system enhances comfort levels while reducing operational costs, making it an attractive option for budget-conscious consumers.

Moreover, the ZQ10 A10B integrates a sophisticated microprocessor control system, enabling precise temperature regulation and simplified user interaction. This intuitive control interface allows users to easily program settings and monitor system performance, leading to a higher degree of comfort and convenience.

The unit is also designed for quiet operation, featuring a sound-dampening casing that minimizes noise levels. This is particularly advantageous in residential environments where noise disturbance can be a significant concern. Additionally, the ZQ10 A10B is equipped with advanced filtration technologies that improve indoor air quality by effectively capturing dust, allergens, and other airborne pollutants, ensuring a healthier living space.

Durability is another hallmark of the Friedrich ZQ10 A10B. Built with high-quality materials, the unit is resistant to corrosion and wear, promising longevity and consistent performance throughout its lifecycle. This resilience makes it a reliable choice in harsh environmental conditions.

Integrated with smart connectivity features, users can control the ZQ10 A10B remotely via smartphone applications, allowing for greater flexibility and ease of use. This integration aligns with the growing trend of smart home technology, appealing to tech-savvy consumers looking for greater control over their heating and cooling systems.

In conclusion, the Friedrich ZQ10 A10B emerges as a leading solution in the HVAC market, combining innovative technology with user-focused design. Its energy efficiency, durability, and advanced features make it a smart investment for anyone looking to enhance their home or business climate control systems while keeping an eye on environmental impact.
Top Page Image Contents