Craftsman 919.724123 owner manual How to Stop, Before Starting, Drain Valve, Check Valve

Page 14

Drain Valve: The drain valve is located at the base of the air tank and is used to drain condensation at the end of each use.

Drain

Valve

Cooling System (not shown): This compressor contains an advanced design cooling system. At the heart of this cooling system is an engineered fan. It is perfectly normal for this fan to blow air through the vent holes

in large amounts. You know that the cooling system is working when air is being expelled.

Air Compressor Pump (not shown): Compresses air into the air tank. Working air is not available until the compressor has raised the air tank pressure above that required at the air outlet.

Check Valve: When the air compressor is operating, the check valve is "open", allowing compressed air to enter the air tank. When the air compressor reaches "cut-out" pressure, the check valve "closes", allowing air pressure to remain inside the air tank.

Check Valve

How to Use Your Unit

How to Stop:

1.Set the On/Auto/Off lever to "OFF".

Before Starting

Break-in Procedure

Serious damage may result if the

following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into service and when the check valve or a complete compressor pump has been replaced.

1.Make sure the On/Auto/Off lever is in the "OFF" position.

NOTE: Pull coupler back until it clicks to prevent air from escaping through the quick connect.

2.Plug the power cord into the correct branch circuit receptacle. (Refer to Voltage and Circuit Protection paragraph in the Installation section of this manual.)

3.Open the drain valve fully (counter-clockwise) to permit air to escape and prevent air pressure build up in the air tank during the break-in period.

4.Set the On/Auto/Off lever to "ON/AUTO" position. The compressor will start.

5.Run the compressor for 15 minutes. Make sure the drain valve is open and there is minimal air pressure build-up in tank.

6.After 15 minutes, close the drain valve (clockwise). The air receiver will fill to "cut-out" pressure and the motor will stop.

The compressor is now ready for use.

A14083

14- ENG

Image 14
Contents AIR Compressor Sold by Sears Canada, Inc. Toronto, Ont. M5B 2B8Table of Contents WarrantyImportant Safety Instructions Specification ChartSafety Guidelines Definitions Hazard What Could HappenAttachments & Accessories To alter the factory set operating pressuresHazard Belt can cause serious injury if Result in serious burnsNever operate the compressor with When Transporting Compressor Glossary AccessoriesAccessories Duty CycleTools Required for Assembly AssemblyContents of Carton Installing Handles Wheels, and Molded Foot BumpersRisk of Electrical InstallationLocation of the Air Compressor Improper Grounding canExtension Cords Voltage and Circuit ProtectionDescription of Operation OperationKnow Your Air Compressor Drain Valve How to StopBefore Starting Check ValveHow to Start Before Each Start-UpCustomer Responsibilities MaintenanceTo Check Safety Valve To Drain TankOutlet Tube Nut Check Valve Service and AdjustmentsTo Replace or Clean Check Valve Screwdriver Open position nothing is visibleGauges Quick StorageTo Replace Regulator Regulator ManifoldTroubleshooting Problem Cause CorrectionBeing used Problem Cause Correction Pour Placer UNE Commande DE Pièces Garantie Complète DE UN AN SUR LES Compresseurs D’AIRConsignes DE Sécurité Importantes Tableau DES SpécificationsMesures DE Sécurité Définitions Conserver ces directives Avertissement Risque dexplosion ou dincendie PréventionAvertissement Risque de projection dobjets Avertissement Risque déclatementRisque Prévention Avertissement Risque de choc électrique Avertissement Risque par inhalationAvertissement Risque de chute Avertissement Risque de brûluresAvertissement Risque relié aux pièces mobiles Risque Avertissement Risque dune utilisation dangereuseAccessoires AccessoiresCycle DE Service LexiqueOutils requis pourlassemblage AssemblageContenu de la boîte Emplacement du compresseur dair Directives DE Mise À LA TerreProtection contre la surtension et protection du circuit RallongesDescription du fonctionnement UtilisationFamiliarisez-vous avec votre compresseur dair Manomètre De sortieRobinet de vidange Arrêt de lappareilAvant le démarrage Robinet de Vidange Système de refroidissement non illustréAvant chaque mise en marche Mise en marcheVérification de la soupape de sûreté EntretienResponsabilités du client Vidange du réservoirTube de sortie Écrou Remplacement ou nettoyage de la soupape de retenueEntretien ET Réglages TournevisManomètres RangementPour remplacer le régulateu Raccords rapidesDépannage Problème Cause CorrectionEst utilisé, ajustez le régulateur Moteur défectueux Remarque 51- FR A14083 Canada MY-HOMESears Parts and Repair Center

919.724123 specifications

The Craftsman 919.724123 is a versatile air compressor designed for various applications, from powering pneumatic tools to inflating tires. This compressor is particularly favored by both DIY enthusiasts and professionals for its reliability and performance.

One of the primary features of the Craftsman 919.724123 is its robust 3.5-gallon steel tank, which provides a substantial air storage capacity. This feature allows for longer working times between refills, making it ideal for users who need sustained air pressure without frequent interruptions. The tank is designed to resist rust and corrosion, ensuring durability and longevity even in tough environments.

The compressor operates with a powerful 1.5 horsepower motor that delivers an efficient performance. It can produce an airflow rate of approximately 2.6 CFM at 90 PSI, which makes it suitable for various tasks ranging from nailing and stapling to painting and more. This ability to maintain a steady stream of air pressure ensures that users can complete their projects without delays.

Equipped with a low-oil pump, the Craftsman 919.724123 promotes a maintenance-free experience, as it eliminates the need for regular oil changes. This feature not only enhances the overall efficiency of the compressor but also extends its life. The oil-free design contributes to easy startup and operation, even in colder temperatures, making it reliable in various conditions.

Portability is another significant advantage of the Craftsman 919.724123. It features a compact design and is lightweight, which makes it easy to transport from one job site to another. The built-in handle adds to its convenience, allowing users to carry it effortlessly.

Safety features are also integrated into the design of the compressor. It comes equipped with a safety valve that prevents pressure from exceeding safe limits, thus protecting both the unit and the user. The easy-to-read gauge allows for quick monitoring of the air pressure, ensuring optimal operation at all times.

In summary, the Craftsman 919.724123 stands out due to its combination of a durable build, efficient performance, and user-friendly features. Its powerful motor, low-maintenance oil-free operation, and portability make it an excellent choice for anyone seeking a reliable air compressor for home or professional use. Whether you are inflating tires or working on wooden projects, this air compressor is equipped to handle a variety of tasks with ease.