Ramsey Electronics LEAD ACID BATTERY CHARGER KIT manual LABC1

Page 13

ˆ5. Install C1, 1000 µF electrolytic capacitor. This part also must be installed properly to function. In fact, this capacitor has the potential to explode if installed in reverse polarity. The PC board silkscreen shows the positive hole and the band on the capacitor shows the negative side. You’ll also note that the lead closest to the stripe is shorter than the other lead; this also indicates the negative side. Save the long leads you clip off from this part. They’re great for the jumpers you’ll need to install later.

Next we’ll install VR1. You’ll need to locate the following parts: the LM317, HS1 is the black finned heatsink, the #4-40 3/8” screw, and the #4-40 kep nut.

ˆ6. Install VR1, the LM317, 3 terminal adjustable regulator. Place the heatsink, HS1, on the circuit board, lining it up with the silkscreen so that the hole in the heatsink matches the hole in the board. Take the LM317 and place it on top of the heatsink so that the hole in the regulator lines up with the other two. This will show you where to bend the leads down so that the part fits in the PC board holes and lays flat on the heatsink. This allows maximum “bleed off” of heat from the part. Once the leads are bent and through their PC board holes, take the screw and nut and attach the LM317 and the heatsink to the board. It is easiest to put the screw through the top of the components and tighten the nut on the bottom of the board. Once the screw is holding everything in place solder the three leads of the LM317.

ˆ7. Install J2, the 2 screw terminal jack. The openings should face the rear of the PC board. This is where the battery you’re charging will be attached to the LABC1.

ˆ8. Install R6, 0.47ohm 1 watt resistor (yellow-violet-silver). This part is physically larger than the other resistors in your kit for a reason; it is a 1 watt part compared to the other 1/4 watt parts. That means it needs to (and can!) dissipate more power than the others.

ˆ9. Install U1, the LM334 IC (three leads TO-92 package marked LM334). Also, keep a few more of those scrap leads handy as we will need a few more jumper wires later.

ˆ10. Install C2, 10 µF electrolytic capacitor. Watch that polarity!

ˆ11. Using a scrap component lead, form a jumper wire and install in the JMP3 holes. Jumpers act like electronic “bridges” that carry power or signals over active traces on the circuit trace side of the board. Solder both ends of the jumper into place.

ˆ12. Install R3, 820 ohms (gray-red-brown).

ˆ13. Take another scrap lead and install JMP2. It helps to pre-bend the wire into a staple shape before inserting into the PC board.

LABC1 • 13

Image 13
Contents Lead Acid Battery Charger KIT Ramsey Transmitter Kits Lead Acid Battery Charger KIT Quick Battery Theory State Specific Open Circuit Description LABC1 LABC1 LABC1 Parts Layout Diagram Capacitors Parts Supplied with Your LABC1 KITResistors and Potentiometers Semiconductors and Integrated CircuitsEnough of that ... let’s get started LABC1 Battery Charger KIT Assembly LABC1 1 3 3 B a c k Front View Front View after Bending Assembly Instructions for Custom Case Temperature J2 Terminal Voltage Adjusting Your LABC1 Battery ChargerSafety Considerations LABC1 Hints Troubleshooting GuideConclusion This page intentionally left blank Ramsey Kit Warranty Additional Suggested Items Required ToolsRamsey ELECTRONICS, INC Fishers Station Drive Victor, New York