Kawasaki 840056 FORWARD/REVERSE and Trigger Lock Lever, To Select the Directions Rotation

Page 43

1.Hold the rear end of the chuck in one hand and use the other hand to rotate the front end in a

counterclockwise direction to open the jaws of the chuck.

2.Insert the shank of the bit (or other accessory) fully into the keyless chuck, taking care to keep the bit in the center of the jaws of the chuck.

LOOSEN

TIGHTEN

HOLD

FORWARD/REVERSE AND TRIGGER LOCK LEVER

Be sure the trigger is released when changing the position of the lever. Always store the tool in the “LOCKED/OFF” position.

Always check the direction of the Cordless Drill's rotation before use.

TO SELECT THE DIRECTIONS

OF ROTATION:

3.Turn the front end of the chuck clockwise to hold the bit in place.

4.Tighten securely by turning the front end of the chuck clockwise while holding the rear end.

OPERATING THE DRILL

Never tape the trigger switch down to provide continu- ous high speed. The tool may fail under such conditions causing fire or

personal injury.

VARIABLE SPEED TRIGGER SWITCH

• To select forward Cordless Drill

rotation, press the trigger lock

TRIGGER

from left to right flat against the Cordless

LOCK

Drill body.

 

• To select reverse, press the trigger lock lever

 

in the opposite direction.

 

• The center position locks the tool.

 

TORQUE SETTINGS

THIS TOOL IS CONTROLLED

BY A TRIGGER SWITCH:

•The speed of the Cordless Drill depends on the amount of pressure you put on the trigger.

•The more pressure you apply, the faster the Cordless Drill will go.

•Release the pressure and the Cordless Drill will slow down.

TRIGGER SWITCH

To prevent damaging the tool or driving screw too deep into work piece, release the trigger when you feel the clutch slip.

THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE:

CONTROL RING

• For light duty work, use lower settings.

 

• For heavy duty work, use higher settings.

PROPER SETTING FOR DRIVING SCREWS: 1. Set the ring on the lowest

setting to begin.

2.Try tightening the first screw. If the drill drives smoothly,

proceed with the next screw.

3. If the Drill’s clutch slips, increase the torque setting and try again until the Drill drives the screw without incident.

13

14

Page 42 Page 44
Image 43
Page 42 Page 44
Contents 19.2V BATTERY-OPERATED Circular SAW Congratulations Table of ContentsGeneral Safety Rules for ALL Battery Operated Tools Recognize Safety SYMBOLS, Words and LabelsWork Area Important SafeguardsElectrical Safety Save These Instructions for Future ReferenceTool USE and Care Personal SafetyService Specific Safety Rules AND/OR SymbolsCauses and Prevention of Kickback Safety Rules for Circular SAWFunctional Description SymbolsSymbol Name Explanation Controls Accessories ComponentsBattery Assembly Removing / Attaching Battery Pack Charging Battery PackAttach Battery Pack Charge Battery PackAttaching / Removing Blade Adjusting Depth and AnglePocket Cutting Operating the Trigger SwitchOperating the Circular SAW General CuttingTool Current Rating Maintenance and CleaningAccessories SpecificationsWhich Extend Beyond the Description on the Face Hereof Year Limited Home USE WarrantyWarranty Disclaimers 19.2V BATTERY-OPERATED Reciprocating SAW Attaching / Removing Blade Operating the Reciprocating SAW Important Safeguards Safety Rules for Cordless Reciprocating SAW Symbols Controls and Components Reciprocating Saw Removing / Attaching Battery PackTo Remove Blade Variable Speed Trigger SwitchThis Tool is Controlled By a Trigger Switch To Attach BladePlunge Cutting Put on eye protectionMetal Cutting Battery Type Ni-Cad Voltage 19.2V Length of Stroke 22mm 7/8 SwitchCharger Input 120V 60Hz Charging Time Approx -5 hours Year Limited Home USE Warranty Warranty Disclaimers 87-1904-60957 Intended USE Table of ContentsRecognize Safety SYMBOLS, Words and Labels CongratulationsService Battery Tool USE and CareSafety Rules for Worklight Component Model Number SymbolsSymbol Name Explanation Functional DescriptionRemoving / Attaching Battery Pack BatteryCharger Replacing the Light Bulb Charging Battery Pack Adjusting the Worklight BeamOperating the on / OFF Switch Operating the WorklightTool Current Rating AccessoriesMaintenance and Cleaning SpecificationsWarranty Performance Year Limited Home USE WarrantyOther Consumer DO-IT-YOURSELF DIY Tools Limitation Of Liability 19.2V 2-SPEED BATTERY-OPERATED Drill Table of Contents Important Safeguards Safety Rules for Cordless Drill / Drivers Symbols Control Ring Battery Pack High/Low Speed Switch690076 Cordless Drill Remove Battery PackNot use the Cordless Drill if the battery Installing Drill BIT Into Keyless ChuckOperating the Drill Torque SettingsFORWARD/REVERSE and Trigger Lock Lever To Select the Directions RotationDrilling Masonry High / LOW Speed Gear ShiftingScrewdriving Drilling MetalVoltage 19.2V Low Speed Conductor Size in A.W.GYear Limited Home USE Warranty Warranty Disclaimers Imprimé dans la Chine Impreso en China Congratulations Symbols Year Limited Home USE Warranty Warranty Disclaimers

840056 specifications

The Kawasaki 840056 is an advanced model that showcases the company's commitment to innovation and performance in the machinery sector. This machine is engineered with a focus on versatility and efficiency, making it ideal for a wide range of applications, from construction to agricultural tasks.

One of the standout features of the Kawasaki 840056 is its powerful engine. The machine is equipped with a cutting-edge, high-performance engine that delivers impressive horsepower while maintaining fuel efficiency. This balance ensures that operators can complete jobs quickly without excessive fuel consumption, minimizing operating costs.

The design of the Kawasaki 840056 emphasizes user comfort and convenience. The cab is spacious, outfitted with ergonomic controls, high visibility, and an intuitive dashboard that provides critical information at a glance. Operators benefit from adjustable seating and climate control options, ensuring that long hours of operation can be undertaken with maximum comfort.

In terms of technology, the Kawasaki 840056 incorporates advanced systems that enhance its operational capabilities. The machine features a state-of-the-art hydraulic system, providing exceptional lifting power and precision. This system is complemented by an innovative load sensing mechanism, which ensures that hydraulic power is used efficiently, adapting automatically to the demands of the task at hand.

Safety is a top priority in the design of the Kawasaki 840056. The machine comes equipped with multiple safety features, including stability monitoring systems, anti-rollover technologies, and implement safety locks. These enhancements not only protect the operator but also ensure the safety of those working nearby.

Additionally, the Kawasaki 840056 is designed for easy maintenance. Access to critical components is simplified, allowing technicians to perform routine checks and repairs quickly. This user-friendly design can significantly reduce downtime, keeping productivity levels high.

Durability is another hallmark of the Kawasaki 840056. Constructed with high-quality materials and engineered to withstand tough working conditions, this machine is built to last. Whether faced with extreme weather or heavy workloads, the Kawasaki 840056 is up to the challenge, making it a reliable choice for professionals in various industries.

In conclusion, the Kawasaki 840056 represents a blend of power, efficiency, and user-friendly features, making it a compelling option for anyone in need of reliable and versatile machinery. With its advanced technologies and focus on safety and comfort, it stands out as a leader in its class.
Top Page Image Contents