Xantrex Technology SW3000 user service Installation Tools and Materials

Page 30

Planning

Installation Tools and Materials

Tools

You will need the following tools to install the Freedom SW 3000 and the battery temperature sensor.

Wire stripper

Crimping tools for fastening lugs and terminals on DC cables

Phillips screwdriver: #2

Slot screwdriver (¼" wide blade max.)

Needle-nose pliers

Wrench for DC terminals: 9/16"

Materials

You will need the following materials to complete your installation:

Strain-relief clamp(s) for AC cables (not provided): 3/4" and/or 1"

DC battery cables sized according to Table 3 on page 13

Terminals and/or crimp connectors for DC cables (for 3/8" stud size)

Copper wire for DC grounding: No. 8 AWG. See “DC Grounding” on page 14

Terminal or crimp connector for DC grounding cable (for 1/4" stud size)

AC and DC disconnect switches and over-current protective devices and connectors as required. See page 13.

AC output and input wire. See Figure 2 on page 8.

If the AC ground wire is stranded, each ground wire requires a ring terminal

Six 1/4"–20 1.25" length steel screws or bolts to mount the Freedom SW 3000

For a list of tools and materials required to install the network, refer to the Xanbus System Installation Guide, which is available for download at www.xantrex.com.

16

Freedom SW 3000 Installation Guide

Image 30
Contents Freedom SW Sine Wave Inverter/Charger Page This guide for use by qualified installers only About This Guide Statement of HazardRelated Information Important Safety Instructions Electrical Shock HazardFire and Burn Hazard Explosion HazardPrecautions When Working With Batteries Precautions When Preparing to Charge Exposure to Chemicals and Gases HazardRisk of Damage to the INVERTER/CHARGER Regulatory Limitations on USEContents Page This guide for use by qualified installers only Page Introduction Materials List Materials ListInstallation Codes Installation InformationBefore You Begin the Installation Electrical Shock and Fire HazardsTypical Xanbus System Diagram About the Xanbus SystemXanbus Enabled System AccessoriesSize and Length of DC Cables Planning the InstallationTwo Key Performance Factors Mounting Location of the Freedom SWPlanning AC, DC, and Network ComponentsPlanning AC Output AC ComponentsAC Input AC LoadsGfci Requirements AC Input ProtectionAC Output Protection Tested GFCIsAC Wiring Distribution PanelsAC Output Neutral Bonding DC Disconnects and Over-Current Devices DC ComponentsBatteries DC CablingDC Grounding Heavy Load Installation Tools and Materials ToolsMaterials Installing the Inverter/Charger OverviewChoosing a Location for the Inverter/Charger Fire and Explosion HazardHeat Hazard Safe BatteryBattery acid Close toMounting the Inverter/Charger ConsiderationsTo mount the inverter/charger By qualified installers only Approved Mounting Orientation Orientation? Connecting the AC Input and AC Output Wires General AC Wiring ConsiderationsFIRE, Electrical SHOCK, and Energy Hazards Connecting AC Input Wires Equipment DamageTo make the AC input connections Connecting the AC Output Wires To make the AC output wiring connectionsDamage other equipment Lines for Single Preparing the Cables Connecting the DC CablesDC Connection Precautions To prepare the DC cablesGuidelines for Routing the DC Cables Electrical Shock and Fire HazardEquipment Damage DUE to Reverse Polarity Connecting the DC Cables to the Inverter/ChargerFire Hazard To connect the DC cablesDC Terminal Covers DC Wiring and DC Grounding To connect the chassis groundConnecting the Battery Temperature Sensor BTS Mounting OptionsMounting to the Negative Battery Terminal To mount the sensor on the negative battery terminalConnecting the BTS Cable to BTS Jack Mounting to the Side of the Battery Case To mount the sensor on the battery caseConnecting to the Network To connect the Freedom SW 3000 to the Xanbus networkPerforming Checks Prior to Initial Start-Up Testing Your Installation Testing in Invert ModeTesting in Charge Mode and AC Bypass Mode Installation CompleteTo verify that the Freedom SW 3000 starts charging Inverter/Charger Physical Specifications Calculating Battery Size Battery InformationBattery Bank Sizing Calculate Battery SizeBattery Information Battery Banks Battery Bank Sizing WorksheetRestrictions on Motor Size = Total watt-hours of AC load between charges Cabling and Hook-up Configurations Parallel ConnectionSeries Connection Batteries Connected in SeriesSeries-Parallel Connections Batteries in Series-Parallel ConnectionsPage Page Xantrex Technology Inc

SW3000 specifications

Xantrex Technology SW3000 is a versatile and powerful inverter that plays a crucial role in providing reliable electrical power to off-grid and mobile applications. Designed specifically for those who require a dependable power source in remote locations or for recreational vehicles, the SW3000 stands out with its excellent features and innovative technologies.

One of the primary characteristics of the SW3000 is its ability to deliver a continuous output of 3000 watts, making it suitable for a wide range of appliances and tools. The inverter can handle startup loads for inductive devices, such as refrigerators and air conditioners, with ease. This capability ensures that users can operate their essential equipment without the worry of overloading the system.

The SW3000 inverter is equipped with advanced Pure Sine Wave technology, ensuring that the output power is clean and stable. Pure Sine Wave inverters are crucial for sensitive electronics, as they provide a smooth power output that mimics the utility grid. This feature protects your devices from potential damage caused by lower-quality inverter systems.

Additionally, the Xantrex SW3000 offers integrated features such as an automatic transfer switch, which seamlessly transfers power between the inverter and utility power when both are available. This ensures uninterrupted operation and convenience for the user. The inverter also has a user-friendly interface, including LED indicators that provide information on the inverter's status, allowing for easy monitoring.

Another significant aspect of the SW3000 is its robust thermal management. The design includes built-in cooling fans that prevent overheating during heavy use, ensuring the longevity of the unit. The inverter also comes with multiple safety features, such as over-voltage, under-voltage, and over-temperature protection, offering peace of mind.

Furthermore, the SW3000 is engineered for easy installation, including versatile mounting options, making it an excellent choice for various applications, from boats and RVs to cabins and backup power systems. Its durable design enables it to withstand harsh environmental conditions, ensuring reliable performance in diverse settings.

Overall, the Xantrex Technology SW3000 inverter combines power capacity, advanced technology, and user-friendly features, making it a top choice for those seeking reliable power solutions in off-grid and mobile environments.