Xantrex Technology SW3000 user service Connecting AC Input Wires, Equipment Damage

Page 38

Installing the Inverter/Charger

Connecting AC Input Wires

Figure 4 shows the wiring compartment, which contains a grounding bus (used to wire the AC input and output gound wires) and a terminal block (used to wire the AC input and AC output connections).

INVERTER AC OUTPUT

LINE 1

AC INPUT

 

LINE 2

AC INPUT

Wiring box cover must be in place during use to reduce risk of injury to persons

AC

IN

AC

OUT

AC GROUNDS

(BEHIND COVER)

Figure 4 AC Wiring Compartment

EQUIPMENT DAMAGE

The terminal block is split into INPUT and OUTPUT sections. Damage may occur if the unit is wired incorrectly.

Do not remove or loosen factory installed wiring.

Failure to follow these instructions can damage the unit and/or damage other equipment.

When making the AC input and AC output connections, observe the correct color code for the appropriate AC wire, as described in Table 2 on page 11.

To make the AC input connections:

1.Locate the wiring compartment cover panel and remove the four screws.

2.Remove the cover panel from the unit to access the wiring compartment.

3.Remove one of the AC knockouts from the front or side of the unit. Do not leave the knockout inside the wiring compartment.

4.Install a strain-relief clamp in the AC knockout.

5.Run the AC wiring through the strain-relief clamp.

6.Strip approximately 2 inches (50 mm) off the jacket from the AC cable and separate the wires.

7.Using a 1/4" blade slot screwdriver, loosen the terminal screws on the terminals. Do not remove the screws.

24

Freedom SW 3000 Installation Guide

Page 37 Page 39
Image 38
Page 37 Page 39
Contents Freedom SW Sine Wave Inverter/Charger Page This guide for use by qualified installers only About This Guide Statement of HazardRelated Information Important Safety Instructions Electrical Shock HazardFire and Burn Hazard Explosion HazardPrecautions When Working With Batteries Risk of Damage to the INVERTER/CHARGER Precautions When Preparing to ChargeExposure to Chemicals and Gases Hazard Regulatory Limitations on USEContents Page This guide for use by qualified installers only Page Introduction Materials List Materials ListInstallation Codes Installation InformationBefore You Begin the Installation Electrical Shock and Fire HazardsTypical Xanbus System Diagram About the Xanbus SystemXanbus Enabled System AccessoriesSize and Length of DC Cables Planning the InstallationTwo Key Performance Factors Mounting Location of the Freedom SWPlanning AC, DC, and Network ComponentsPlanning AC Output AC ComponentsAC Input AC LoadsGfci Requirements AC Input ProtectionAC Output Protection Tested GFCIsAC Wiring Distribution PanelsAC Output Neutral Bonding DC Disconnects and Over-Current Devices DC ComponentsBatteries DC CablingDC Grounding Heavy Load Materials Installation Tools and MaterialsTools Installing the Inverter/Charger OverviewHeat Hazard Choosing a Location for the Inverter/ChargerFire and Explosion Hazard Safe BatteryBattery acid Close toTo mount the inverter/charger Mounting the Inverter/ChargerConsiderations By qualified installers only Approved Mounting Orientation Orientation? FIRE, Electrical SHOCK, and Energy Hazards Connecting the AC Input and AC Output WiresGeneral AC Wiring Considerations To make the AC input connections Connecting AC Input WiresEquipment Damage Damage other equipment Connecting the AC Output WiresTo make the AC output wiring connections Lines for Single Preparing the Cables Connecting the DC CablesDC Connection Precautions To prepare the DC cablesGuidelines for Routing the DC Cables Electrical Shock and Fire HazardEquipment Damage DUE to Reverse Polarity Connecting the DC Cables to the Inverter/ChargerFire Hazard To connect the DC cablesDC Terminal Covers DC Wiring and DC Grounding To connect the chassis groundConnecting the Battery Temperature Sensor BTS Mounting OptionsMounting to the Negative Battery Terminal To mount the sensor on the negative battery terminalConnecting the BTS Cable to BTS Jack Mounting to the Side of the Battery Case To mount the sensor on the battery caseConnecting to the Network To connect the Freedom SW 3000 to the Xanbus networkPerforming Checks Prior to Initial Start-Up Testing Your Installation Testing in Invert ModeTo verify that the Freedom SW 3000 starts charging Testing in Charge Mode and AC Bypass ModeInstallation Complete Inverter/Charger Physical Specifications Calculating Battery Size Battery InformationBattery Bank Sizing Calculate Battery SizeBattery Information Restrictions on Motor Size Battery BanksBattery Bank Sizing Worksheet = Total watt-hours of AC load between charges Cabling and Hook-up Configurations Parallel ConnectionSeries Connection Batteries Connected in SeriesSeries-Parallel Connections Batteries in Series-Parallel ConnectionsPage Page Xantrex Technology Inc

SW3000 specifications

Xantrex Technology SW3000 is a versatile and powerful inverter that plays a crucial role in providing reliable electrical power to off-grid and mobile applications. Designed specifically for those who require a dependable power source in remote locations or for recreational vehicles, the SW3000 stands out with its excellent features and innovative technologies.

One of the primary characteristics of the SW3000 is its ability to deliver a continuous output of 3000 watts, making it suitable for a wide range of appliances and tools. The inverter can handle startup loads for inductive devices, such as refrigerators and air conditioners, with ease. This capability ensures that users can operate their essential equipment without the worry of overloading the system.

The SW3000 inverter is equipped with advanced Pure Sine Wave technology, ensuring that the output power is clean and stable. Pure Sine Wave inverters are crucial for sensitive electronics, as they provide a smooth power output that mimics the utility grid. This feature protects your devices from potential damage caused by lower-quality inverter systems.

Additionally, the Xantrex SW3000 offers integrated features such as an automatic transfer switch, which seamlessly transfers power between the inverter and utility power when both are available. This ensures uninterrupted operation and convenience for the user. The inverter also has a user-friendly interface, including LED indicators that provide information on the inverter's status, allowing for easy monitoring.

Another significant aspect of the SW3000 is its robust thermal management. The design includes built-in cooling fans that prevent overheating during heavy use, ensuring the longevity of the unit. The inverter also comes with multiple safety features, such as over-voltage, under-voltage, and over-temperature protection, offering peace of mind.

Furthermore, the SW3000 is engineered for easy installation, including versatile mounting options, making it an excellent choice for various applications, from boats and RVs to cabins and backup power systems. Its durable design enables it to withstand harsh environmental conditions, ensuring reliable performance in diverse settings.

Overall, the Xantrex Technology SW3000 inverter combines power capacity, advanced technology, and user-friendly features, making it a top choice for those seeking reliable power solutions in off-grid and mobile environments.
Top Page Image Contents