Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 Programming, Standard setting

Page 21

STUDER INNOTEC

HP-COMPACT

actual temperatures, a temperature sensor can be connected to the HP-COMPACT. The compensation through the sensor is –3mV/°C/Cell.

Order Number: CT-35

Dimensions: H x B x T / 58 x 51.5 x 22mm

4.11 Remote control for „Power Sharing“ RPS-01

If the Remote control RPS-01 is installed, the Trimmer

(26)“INPUT LIMIT“ has to be set on the value max.. The HP-COMPACT takes into account the lowest values set on the inverter and on the Remote control.

The current available at the HP-COMPACT input will be determined by the power of the connected source (generator, grid etc...). The potentiometer on the RPS-

01 must be adjusted lower or equal to max. value of the power source.

For instance if the source is a generator of 2000 Watt, the potentiometer has to be set at max. 8A. This value is obtained in dividing 2000 Watt by 230V. If the HP- COMPACT is connected to a power source which is protected by a 6A circuit breaker, the potentiometer must be set at a max. value of 6A.

Caution: the HP-COMPACT will not limit if an appliance draws more current than available from the source ! This means that the connected generator will be over-loaded or that the circuit-breaker before the HP-COMPACT will break.

5 Programming

The HP-COMPACT (except for 60Hz versions) is equipped with a Flash processor fitted out with EEPROM Memory, which means that even when it is disconnected from the battery, the parameters that were programmed for the application remain after a new connection to the battery.

It is possible to reinitialize (RESET) the HP-COMPACT by pressing simultaneously on the three push buttons 19/20/21 during at least 2 seconds. A beep will confirm the RESET. The inverter switches off after this operation. It can be turned on again after the beep. The programmed parameters will remain.

5.1Standard setting

The HP-COMPACT is delivered with the following default settings:

Auxiliary contact: active in case of defect or manual turn off with the LED 10/11/12/13

Battery voltage :

Low voltage

11.6V / 23.2V / 46.4V

 

Float Charge

13.5V / 27.0V / 54.0V

 

End of Charge Voltage

14.4V / 28.8V / 57.6V

 

Equalization

15.6V / 31.2V / 62.4V

Absorption Time :

 

2 Hours

Equalizing Time :

 

20 Minutes

HP-COMPACT V5.4

23/80

Page 20 Page 22
Image 21
Page 20 Page 22
Contents HP-COMPACT HPC Sine wave Inverter, Battery charger, TransfersystemHP-COMPACT Warranty Disclaimer Quality and WarrantyGeneral Information Operating instructionsLiability Disclaimer Special precautionsIntroduction Principle schematicDescription of the main functions Battery connecting Installation place Mounting and installingFixing ConnectionsCabling Pre-installation settingsConnection to battery 3.6.1.1 On the appliance side Connection to Temperature Sensor Temp Connection to Remote controlConnection to the 230Vac-consumer appliances AC Output Connection to the 230Vac Input AC InputDisplay and control parameters ControlLED Light Emitting Diodes LEDTurning Knobs Push buttonsInverter Charge detection system „StandbyOverheating Over Temp Battery ConditionDefault values for battery voltage thresholds Battery chargerCycle of charge Equalization chargingInput current repartition Power sharing Set the Input LimitCharging current Transfer system Delayed mode of the Transfer System Fast UPS- Mode for the Transfer SwitchMultifunctional Contact Set the transfer voltage thresholdHP-COMPACT Remote Control RCC-01Remote control for „Power Sharing RPS-01 Standard settingProgramming Reset value default settings Battery voltages and absorption timeSet the voltage and timing threshold Table of voltage and timing threshold Auxiliary contactPrinciple Programming of the Auxiliary ContactManual operating of Auxiliary Contact Power cut of the second priority loadsDiagram of the different modes Installation MaintenanceDisabling some of the HP-COMPACT functions Declaration of CE ComplianceTechnical Data

HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 specifications

Studer Innotec is a Swiss company renowned for its innovative and high-quality inverter chargers. Among their notable products are the HPC series inverters: HPC 2800-12, HPC 4400-24, HPC 600-48, and HPC 6000-48. These models are designed for a wide range of applications, from residential use to commercial and industrial environments, delivering reliable power solutions.

The HPC 2800-12 is a robust inverter charger designed for 12V systems. It has a continuous power output of 2800W, making it suitable for various off-grid applications. Its advanced technology allows for a pure sine wave output, ensuring compatibility with sensitive electronic devices. A standout feature is its intelligent battery management system that optimizes charging processes to prolong battery life and enhance efficiency.

Moving up to the HPC 4400-24, this model operates at 24V and boasts a powerful output of 4400W. This inverter charger is ideal for larger systems that require substantial power. It features a high surge capacity, allowing it to handle heavy loads and start demanding appliances effortlessly. The digital display provides users with vital information on system performance, making it easier to monitor and manage energy consumption.

The HPC 600-48 is a compact yet powerful 48V inverter charger delivering a continuous output of 600W. It combines versatility with performance, making it suitable for smaller applications and mobile setups. Like its siblings, the HPC 600-48 also features pure sine wave technology and advanced protections against overload, short circuit, and overheating, ensuring safe operation under various conditions.

For high-demand applications, the HPC 6000-48 stands out with an impressive output of 6000W. Designed for larger setups, this model is capable of powering multiple appliances simultaneously. It incorporates advanced network technology, allowing parallel operation for increased power capacity when connecting multiple units. Moreover, its modular design enables easy customization to meet specific power requirements.

All models within the Studer Innotec HPC series boast key technologies such as programmable charging profiles, advanced monitoring capabilities, and a built-in protection system. Their robust construction ensures durability and reliability, making them suitable for various environments. With a commitment to quality and performance, the Studer Innotec HPC series continues to be a preferred choice for users seeking dependable power solutions in both commercial and residential settings.
Top Page Image Contents