Studer Innotec HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 manual Cabling

Page 9

STUDER INNOTEC

HP-COMPACT

A

Battery +/-

Connection terminal (M8) for battery cable (HPC 4400-24/6000-

 

 

48/8000-48 with fuse)

B

Reserved

-

CRemote contr. Connection terminal for Remote Control RCC-01

DTransfer delay Slide switch for Transfer Delay

E

Equalize

Slide switch for equalization of the Battery

F

Temp.

Connection terminal for Temperature sensor CT-35 and/or

 

 

Remote Power Sharing RPS-01

G

Aux. Contact

Connection terminal for Auxiliary Contact

H

AC Input

Connection terminal for AC-input

J

ID Plate

Identification plate with Technical data and Serial number

K

AC Output

Connection terminal for AC-output

L

Reserved

-

M

Hole

Pass through hole for RCC-01, CT-35 and RPS-01

N

Protection

Thermal circuit breaker 30A (50A for HPC 8000-48) for the

 

 

Transfer system

3.5Cabling

Connecting the HP-COMPACT is a very important step of the installation. You must take care that all connection work is carried out in a clean and correct way and that under no circumstance a cable is connected to a wrong terminal.

Connecting of the HP-COMPACT must be carried out in the following order. In case

of dismantling this order must be reversed.

3.6Pre-installation settings

Before you start with the cabling of the HP-COMPACT you must set the type of battery. In case sealed-gel batteries are used then you must set the small slide- switch „Equalize“ which is on the front with the connection terminals, in OFF position. In case of „normal“ lead-acid – batteries, these can handle a higher equalizing

HP-COMPACT V5.4

11/80

Page 8 Page 10
Image 9
Page 8 Page 10
Contents HP-COMPACT HPC Sine wave Inverter, Battery charger, TransfersystemHP-COMPACT Warranty Disclaimer Quality and WarrantyGeneral Information Operating instructionsLiability Disclaimer Special precautionsIntroduction Principle schematicDescription of the main functions Battery connecting Installation place Mounting and installingFixing ConnectionsCabling Pre-installation settingsConnection to battery 3.6.1.1 On the appliance side Connection to Temperature Sensor Temp Connection to Remote controlConnection to the 230Vac-consumer appliances AC Output Connection to the 230Vac Input AC InputDisplay and control parameters ControlLED Light Emitting Diodes LEDTurning Knobs Push buttonsInverter Charge detection system „StandbyOverheating Over Temp Battery ConditionDefault values for battery voltage thresholds Battery chargerCycle of charge Equalization chargingInput current repartition Power sharing Set the Input LimitCharging current Transfer system Delayed mode of the Transfer System Fast UPS- Mode for the Transfer SwitchMultifunctional Contact Set the transfer voltage thresholdHP-COMPACT Remote Control RCC-01Remote control for „Power Sharing RPS-01 Standard settingProgramming Reset value default settings Battery voltages and absorption timeSet the voltage and timing threshold Table of voltage and timing threshold Auxiliary contactPrinciple Programming of the Auxiliary ContactManual operating of Auxiliary Contact Power cut of the second priority loadsDiagram of the different modes Installation MaintenanceDisabling some of the HP-COMPACT functions Declaration of CE ComplianceTechnical Data

HPC 2800-12, HPC 4400-24, HPC 600-48, HPC 6000-48 specifications

Studer Innotec is a Swiss company renowned for its innovative and high-quality inverter chargers. Among their notable products are the HPC series inverters: HPC 2800-12, HPC 4400-24, HPC 600-48, and HPC 6000-48. These models are designed for a wide range of applications, from residential use to commercial and industrial environments, delivering reliable power solutions.

The HPC 2800-12 is a robust inverter charger designed for 12V systems. It has a continuous power output of 2800W, making it suitable for various off-grid applications. Its advanced technology allows for a pure sine wave output, ensuring compatibility with sensitive electronic devices. A standout feature is its intelligent battery management system that optimizes charging processes to prolong battery life and enhance efficiency.

Moving up to the HPC 4400-24, this model operates at 24V and boasts a powerful output of 4400W. This inverter charger is ideal for larger systems that require substantial power. It features a high surge capacity, allowing it to handle heavy loads and start demanding appliances effortlessly. The digital display provides users with vital information on system performance, making it easier to monitor and manage energy consumption.

The HPC 600-48 is a compact yet powerful 48V inverter charger delivering a continuous output of 600W. It combines versatility with performance, making it suitable for smaller applications and mobile setups. Like its siblings, the HPC 600-48 also features pure sine wave technology and advanced protections against overload, short circuit, and overheating, ensuring safe operation under various conditions.

For high-demand applications, the HPC 6000-48 stands out with an impressive output of 6000W. Designed for larger setups, this model is capable of powering multiple appliances simultaneously. It incorporates advanced network technology, allowing parallel operation for increased power capacity when connecting multiple units. Moreover, its modular design enables easy customization to meet specific power requirements.

All models within the Studer Innotec HPC series boast key technologies such as programmable charging profiles, advanced monitoring capabilities, and a built-in protection system. Their robust construction ensures durability and reliability, making them suitable for various environments. With a commitment to quality and performance, the Studer Innotec HPC series continues to be a preferred choice for users seeking dependable power solutions in both commercial and residential settings.
Top Page Image Contents