Hitachi C 10LA Cutting Operations, Ripping FIG. T, U, Bevel Ripping, Ripping Small Pieces

Page 19

CUTTING OPERATIONS

There are two basic types of cuts: ripping and crosscutting. Ripping is cutting along the length and the grain of the workpiece. Crosscutting is cutting either across the width or across the grain of the workpiece. Neither ripping nor crosscutting may be done safely freehand. Ripping requires the use of the rip fence, and crosscutting requires the miter gauge.

WARNING

English

Fig. T

Before using the saw each and every time, check the following:

1.The blade is tightened to the arbor.

2.The bevel angle lock knob is tight.

3.If ripping, the fence is locked into position & is parallel to the miter gauge groove.

4.The blade guard is in place and working properly.

5.Safety glasses are being worn.

The failure to adhere to these common safety rules, and those printed in the front of this manual, can greatly increase the likelihood of injury.

RIPPING (FIG. T, U)

WARNING

To prevent serious injury:

•

Never use a miter gauge when ripping.

•

Never use more than one rip fence during a

 

single cut.

1

NOTE : Always use a push stick. When width of the rip is narrower than 2” the push stick cannot be used because the guard will interfere…therefore, use the auxiliary fence so the push stick can be used as shown on page 25.

7.Keep your thumbs off the table top. When both of your thumbs touch the front edge of the table (2),

fi nish the cut with a push stick. To make an additional push stick, use the pattern on page 25.

8.The push stick (3) should always be used. (Fig. U)

9.Continue pushing the workpiece with the push stick (3) until it passes through the blade guard and clears the rear of the table.

10.Never pull the piece back when the blade is turning.

Turn the switch OFF. When the blade completely stops, you can then remove the workpiece.

•

Do not allow familiarity or frequent use of your

 

table saw to cause careless mistakes. Remember

 

that even a careless fraction of a second is

 

enough to cause a severe injury.

•

Keep both hands away from the blade and clear

•

from the path of the blade.

The workpiece must have a straight edge against

 

the fence and must not be warped, twisted, or

 

bowed when ripping.

1.

Remove the miter gauge and store it in the “storage”

 

compartment in the base of the saw.

2.

Secure the rip fence to the table.

3.

Raise the blade so it is about 1/8” higher than the top

 

of the workpiece.

Fig. U

2

BEVEL RIPPING

3

1

4.

Place the workpiece fl at on the table and against the

 

fence. Keep the workpiece away from the blade.

5.

Turn the saw ON and wait for the blade to come to

 

full speed.

6.

Slowly feed the workpiece into the blade by pushing

 

forward only on the workpiece section (1) that will

 

pass between the blade and the fence. (Fig. T)

WARNING

AVOID KICKBACK by pushing forward on the section of the workpiece that passes between the blade and the fence. Never perform any freehand operations.

– 19

This cut is the same as ripping except the blade bevel angle is set to an angle other than “0°”.

RIPPING SMALL PIECES

To avoid injury from the blade contact, never make cuts narrower than 1/2” wide.

1.It is unsafe to rip small pieces. Instead, rip a larger piece to obtain the size of the desired piece.

2.When a small width is to be ripped and your hand cannot be safely press between the blade and the rip fence, use one or more push sticks to move the workpiece. Always use a push stick during ripping operations.

–

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Mode D’EMPLOI ET Instructions DE Securite Contents Motor SAW Product SpecificationsEnglish Power Tool SafetyTable SAW Safety Electrical Requirements and Safety Tools Needed for Assembly Accessories and AttachmentsCarton Contents Unpacking Your Stationary Table SAW Know Your Stationary Table SAW Blade Elevation Handwheel Raises Glossary of TermsHitachi Professional Table SAW Terms Woodworking TermsAssembly the front rail Fig. B-1 Assembly and AdjustmentsAssembly the Table Extension FIG. B Assembly the Front and Rear Table Rail FIG. B-1, B-2Blade Raising Handwheel FIG. D English Assembly the rear table rail Fig. B-2Assembly the Rear Table Extension FIG. C Blade Guard Assembly FIG. E, FFig. F Aligning the Blade Guard Splitter FIG. FRemoving the Blade FIG. G Installing a Blade FIG. GBlade Tilting Indicator FIG. J Adjusting the 90O and 45O Positive Stops FIG. H, H-190O Stop Fig. H, H-1 Rip fence and miter gauge Fig. L Installing the Table Insert FIG. KPower Cord FIG. M Miter Gauge Adjustment FIG. N Storage FIG. L, MRIP Fence Indicator FIG. Q RIP Fence Adjustment FIG. ORIP Fence Operation Basic SAW Operations OperationRipping Small Pieces Cutting OperationsRipping FIG. T, U Bevel RippingBevel Crosscutting FIG Using Wood Facing on the Miter Gauge FIG. WCrosscutting FIG To prevent serious injuryAuxiliary Fence FIG. BB Using Wood Facing on the RIP Fence FIG. AACompound Miter Crosscutting FIG. Y Miter CUT FIG. ZClamps. Fig. CC English Attach auxiliary fence to rip fence with two CDado Cuts FIG. DD Blade Raising and Tilting Mechanism FIG. EE MaintenanceGeneral Maintenance Maintaining Your Table SAWSymptom Troubleshooting GuidePossible Causes Corrective Action Push Stick Construction Description Size Parts ListStationary Table SAW Model NO. C10LA Schematic 120V & 240V Wire Wirding Hitachi Koki Canada Co

C 10LA specifications

The Hitachi C 10LA is a powerful and versatile miter saw that stands out in the realm of woodworking and construction tools. Known for its precision, efficiency, and durability, this saw is designed to meet the needs of both professional contractors and DIY enthusiasts.

One of the main features of the Hitachi C 10LA is its robust 15-amp motor, which delivers a remarkable no-load speed of up to 5,000 RPM. This high-speed capability allows users to make clean and accurate cuts through various materials, including hardwood, softwood, and even composite materials. The saw’s large cutting capacity provides a maximum miter cut of 52 degrees to the right and 45 degrees to the left, along with a maximum bevel cut of 45 degrees. This range of motion makes it ideal for creating precise angled cuts, commonly required for crown molding and other intricate woodworking projects.

The C 10LA also features a unique laser marker system that enhances cutting accuracy. This technology projects a laser line onto the workpiece, indicating exactly where the blade will cut, thereby eliminating guesswork and reducing the risk of errors. Additionally, the saw is equipped with a large, sturdy base, providing stability during use and reducing vibration for smoother operation.

Safety is a significant consideration in the design of the Hitachi C 10LA. It includes an electric brake that halts the blade almost instantly after the trigger is released, ensuring that users can operate the saw with confidence. Its dust collector attachment helps maintain a clean work environment by capturing sawdust and debris, which not only improves visibility but also promotes a safer workspace.

The C 10LA’s lightweight design, weighing approximately 26.3 lbs, coupled with a comfortable handle, makes it easy to transport and maneuver, whether in a workshop or on a job site. The saw is also designed for easy blade changes and maintenance, further enhancing its usability and convenience.

In summary, the Hitachi C 10LA miter saw combines powerful performance with advanced features, making it a reliable choice for tradespeople and hobbyists alike. With its high-speed motor, accurate laser guide, impressive cutting capacity, and safety features, it is well-equipped to handle a wide variety of cutting tasks with precision and ease.
Top Page Image Contents