Harbor Freight Tools 66630 Aligning and Adjusting the Rip Fence, Adjusting Table Insert

Page 13

Aligning and Adjusting the Rip Fence (146)

1.WARNING! A misaligned Fence can cause kickbacks and jams. To reduce risk of injury, always maintain proper Fence alignment. The Rip Fence must be parallel with the Blade and Table grooves.

2.Lift up the Fence Handle (26) and move the Fence along the gauge slot until sliding it to the desired location.

3.Verify that Fence is parallel, then push down on the Handle to lock the Fence in place.

4.A Draw Pole (132) locks the Fence in place. To adjust the Draw Pole, loosen the Bolt (20) that connects the Draw Pole to the Fence.

5.WARNING! The Fence must be properly aligned to the gauge slot to prevent kickback during ripping.

6.To check for proper alignment, po- sition the Fence next to the gauge slot and clamp Fence to the Table by pushing down on Fence Handle. Once locked, the edge of the Fence should be parallel to the gauge slot.

Adjusting Table Insert (112)

1.Lower the Blade by turning the Hand- wheel clockwise.

2.Loosen the two Table Insert Bolts (12).

3.Adjust the Table Insert and retighten, making sure to not overtighten. Do- ing so can cause the Table Insert to bow or bend.

4.If the Table Insert is slightly above the Table, tighten the two Table Insert

Bolts until the Table Insert is flush

with or slightly below the Table sur- face.

Miter Gauge (100) Operation and

Adjustment

1.When straight cross-cutting (the Blade is set at 90° to the Table) the Miter Gauge can be used in either table slot.

2.When bevel cross-cutting (the Blade is tilted away) only use the Miter Gauge in the right table slot where the Blade is titled away from the Miter Gauge and your hands.

3.To operate the Miter Gauge, loosen the Gauge’s Lock Knob (101) and move the Gauge to the desired angle, then tighten Knob.

Adjusting Blade Parallel To Miter Gauge

Slots

1.WARNING! Make sure to unplug Table Saw before making any adjust- ments to Blade.

2.To prevent kickback and ensure ac- curate cuts when cutting, the Blade’s angle in relation to the Miter Gauge should be regularly checked. If any adjustments are needed:

3.Remove the Blade Guard (113).

4.Raise the Blade to its highest position and adjust to Blade so that it is 90° to the Table.

5.Mark a Blade tooth at the front of the Table Saw with a marker.

6.Using a square or ruler (not includ- ed), place the square against the

Miter Gauge slot and adjust the flat

SKU 66630

For technical questions, please call 1-800-444-3353.

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Distributed exclusively by Harbor Freight Tools For technical questions or replacement parts, please callSave This Manual General Tool Safety WarningsSave all warnings and instructions for future reference For technical questions, please callTable a 25’ 50’ 100’ 150’Not a safe method Table Saw Safety WarningsFor technical questions, please call Diagram not to scale Essential Straight Push-stick Features FunctionsHandle Notch Stick LengthVibration Safety Grounded Tools Tools with Three Prong Plugs Grounding InstructionsOutlets for 2-Prong Plug Double Insulated Tools Tools With Two Prong PlugsAssembly SpecificationsUnpacking Instructions for putting into useOperating Instructions Table Saw AdjustmentsMounting 90 Positive Stop Adjustment Blade Depth and Angle AdjustmentAdjusting Table Insert Aligning and Adjusting the Rip FenceMiter Gauge 100 Operation Adjustment Adjusting Blade Parallel To Miter Gauge SlotsFigure B Installing/Replacing Saw BladeGeneral Operating Instructions Work Piece and Work Area Set UpAvoiding Kickback Making a Rip-cut Making a Cross-cutMaking a Bevel Rip-cut Cleaning, Maintenance, Lubrication Maintenance ServicingPart Description Qty Parts ListRecord Product’s Serial Number Here Please Read the Following CarefullyAssembly Diagram Limited 1 year / 90 Day warranty

66630 specifications

Harbor Freight Tools 66630 is a versatile six-gallon portable air compressor that caters to both novice DIY enthusiasts and seasoned professionals. Its compact and lightweight design makes it easy to transport, while still delivering robust performance for a wide range of applications.

One of the standout features of the 66630 is its powerful 1.5 horsepower motor, which is designed for maximum efficiency and durability. The motor operates at a low RPM, reducing wear and tear while ensuring quieter operation. With a maximum pressure of 125 PSI, this air compressor is capable of handling a variety of pneumatic tools such as nail guns, airbrushes, and impact wrenches, making it a valuable addition to any toolbox.

The 66630's six-gallon vertical tank design maximizes air storage without taking up excessive floor space. This feature is particularly advantageous for those who have limited workshop areas. The tank is made of high-quality steel, providing durability and resistance to rust and corrosion, which prolongs the compressor's life.

In terms of technologies, the Harbor Freight Tools 66630 utilizes an oil-free pump system. This means less maintenance is required, as users do not need to worry about oil changes or oil spills. The oil-free pump also contributes to cleaner air output, making it more suitable for tasks like painting or inflating sports equipment.

Safety is another priority with this compressor. It is equipped with a thermal overload protector that prevents the motor from overheating during prolonged use. The built-in pressure regulator allows users to adjust and control air pressure, ensuring compatibility with various tools and applications.

Additionally, the 66630's ergonomic handle and rubber feet enhance portability and stability. The handle provides a comfortable grip for easy transport, while the rubber feet reduce vibrations, ensuring the compressor remains stable during operation.

Overall, the Harbor Freight Tools 66630 air compressor stands out for its combination of power, portability, and user-friendly features. Its versatility makes it suitable for various tasks, from home repairs to professional projects, solidifying its place as a reliable tool in any workshop. Whether for inflating tires, powering tools, or completing a range of home improvement tasks, the 66630 provides the performance needed to get the job done efficiently.
Top Page Image Contents