Harbor Freight Tools 66630 Blade Depth and Angle Adjustment, Positive Stop Adjustment

Page 12

Blade Depth and Angle Adjustment

1.The Blade (96) depth should be set so that outer points of the Blade are 1/8” to 1/4” higher than the workpiece while the lowest points are below the workpiece.

2.To raise the Blade, turn the Hand- wheel (29) counterclockwise.

3.To lower the Blade, turn the Hand- wheel clockwise.

4.To adjust the Blade’s angle, loosen the Bevel Lock Knob (62) and then turn the Handwheel until the Blade reaches the desired angle. Then tighten the Bevel Lock Knob. See Figure A, below.

7.Please note: When the Blade is at 90° to the Table Saw, the Blade should be square with the Saw Table.

8.WARNING! The Bevel Lock Knob must be tightened during all cutting operations.

45° and 90° Positive Stop Adjustment

1.The Table Saw is equipped with positive stops for rapid and accurate positioning of the Blade at 45° and 90° to the table.

2.Before making ANY adjustments, make sure the Table Saw is un- plugged and the Switch is removed.

3.To adjust the positive stop at 90°, loosen the Bevel Lock Knob and move as far to the left as possible. Then tighten the Knob.

Bevel Lock 4. Knob (62)

Place a level or square (not included) on the Table (109) with one end blade to make sure Blade is at 90°. If not, loosen the Bolt (110) a few turns and tilt Blade until at the correct angle.

 

Handwheel

Switch (17)

(29)

Figure A

5.When the Blade is tilted to the left as far as it will go, the Blade should be at a 45° angle to the Saw Table and the Bevel Indicator on the Ruler (13) should point to 45°.

6.When the Blade is tilted to the right as far as it will go, the Blade should be at a 90° angle to the Saw Table and the Bevel Indicator on the Ruler should point to 0°.

5.Tighten the Bevel Lock Knob and then tighten the Bolt (110).

6.To adjust the positive stop at 45°, loosen the Bevel Lock Knob and and move as far to the right as possible. Then tighten the Knob.

7.Place a level or square on the Table with one end blade to make sure Blade is at 45°. If not, loosen the Bolt (111) a few turns and tilt Blade until at the correct angle.

8.Tighten the Bevel Lock Knob and then tighten the Bolt (111).

SKU 66630

For technical questions, please call 1-800-444-3353.

Page 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents For technical questions or replacement parts, please call Distributed exclusively by Harbor Freight ToolsGeneral Tool Safety Warnings Save This ManualSave all warnings and instructions for future reference For technical questions, please call25’ 50’ 100’ 150’ Table aTable Saw Safety Warnings Not a safe methodFor technical questions, please call Essential Straight Push-stick Features Functions Diagram not to scaleHandle Notch Stick LengthVibration Safety Grounding Instructions Grounded Tools Tools with Three Prong PlugsDouble Insulated Tools Tools With Two Prong Plugs Outlets for 2-Prong PlugSpecifications AssemblyUnpacking Instructions for putting into useTable Saw Adjustments Operating InstructionsMounting Blade Depth and Angle Adjustment 90 Positive Stop AdjustmentAligning and Adjusting the Rip Fence Adjusting Table InsertMiter Gauge 100 Operation Adjustment Adjusting Blade Parallel To Miter Gauge SlotsInstalling/Replacing Saw Blade Figure BWork Piece and Work Area Set Up General Operating InstructionsAvoiding Kickback Making a Cross-cut Making a Rip-cutMaking a Bevel Rip-cut Maintenance Servicing Cleaning, Maintenance, LubricationParts List Part Description QtyPlease Read the Following Carefully Record Product’s Serial Number HereAssembly Diagram Limited 1 year / 90 Day warranty

66630 specifications

Harbor Freight Tools 66630 is a versatile six-gallon portable air compressor that caters to both novice DIY enthusiasts and seasoned professionals. Its compact and lightweight design makes it easy to transport, while still delivering robust performance for a wide range of applications.

One of the standout features of the 66630 is its powerful 1.5 horsepower motor, which is designed for maximum efficiency and durability. The motor operates at a low RPM, reducing wear and tear while ensuring quieter operation. With a maximum pressure of 125 PSI, this air compressor is capable of handling a variety of pneumatic tools such as nail guns, airbrushes, and impact wrenches, making it a valuable addition to any toolbox.

The 66630's six-gallon vertical tank design maximizes air storage without taking up excessive floor space. This feature is particularly advantageous for those who have limited workshop areas. The tank is made of high-quality steel, providing durability and resistance to rust and corrosion, which prolongs the compressor's life.

In terms of technologies, the Harbor Freight Tools 66630 utilizes an oil-free pump system. This means less maintenance is required, as users do not need to worry about oil changes or oil spills. The oil-free pump also contributes to cleaner air output, making it more suitable for tasks like painting or inflating sports equipment.

Safety is another priority with this compressor. It is equipped with a thermal overload protector that prevents the motor from overheating during prolonged use. The built-in pressure regulator allows users to adjust and control air pressure, ensuring compatibility with various tools and applications.

Additionally, the 66630's ergonomic handle and rubber feet enhance portability and stability. The handle provides a comfortable grip for easy transport, while the rubber feet reduce vibrations, ensuring the compressor remains stable during operation.

Overall, the Harbor Freight Tools 66630 air compressor stands out for its combination of power, portability, and user-friendly features. Its versatility makes it suitable for various tasks, from home repairs to professional projects, solidifying its place as a reliable tool in any workshop. Whether for inflating tires, powering tools, or completing a range of home improvement tasks, the 66630 provides the performance needed to get the job done efficiently.
Top Page Image Contents