293741 -
MOTOR
Many
CAUTION: Do not operate your tool on a current on which the voltage is not within correct limits. Do not operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor damage. A table of recommended extension cord sizes will be found in this section. This table is based on limiting line voltage drop to 5 volts (10 volts for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
Nameplate Ampere Rating
115V | 25 Ft. | 50 Ft. | 100 Ft. | 150 Ft. | 200 Ft. | 250 Ft. | 300 Ft. | 400 Ft. | 500 Ft. |
230V | 50 Ft. | 100 Ft. | 200 Ft. | 300 Ft. | 400 Ft. | 500 Ft. | 600 Ft. | 800 Ft. | 1000 Ft. |
| 18 | 18 | 18 | 16 | 16 | 14 | 14 | 12 | 12 |
|
|
|
|
|
|
|
|
|
|
18 | 18 | 16 | 14 | 14 | 12 | 12 | 10 | 10 | |
|
|
|
|
|
|
|
|
|
|
18 | 18 | 16 | 14 | 12 | 12 | 10 | 10 | 8 | |
18 | 18 | 14 | 12 | 12 | 10 | 10 | 8 | 8 | |
|
|
|
|
|
|
|
|
|
|
18 | 16 | 14 | 12 | 10 | 10 | 8 | 8 | 6 | |
|
|
|
|
|
|
|
|
|
|
18 | 16 | 12 | 10 | 10 | 8 | 6 | 6 | 6 | |
18 | 14 | 12 | 10 | 8 | 8 | 6 | 6 | 4 | |
|
|
|
|
|
|
|
|
|
|
16 | 14 | 10 | 8 | 8 | 6 | 6 | 4 | 4 | |
|
|
|
|
|
|
|
|
|
|
16 | 12 | 10 | 8 | 6 | 6 | 6 | 4 | 2 | |
16 | 12 | 10 | 8 | 6 | 6 | 4 | 4 | 2 | |
|
|
|
|
|
|
|
|
|
|
14 | 12 | 8 | 8 | 6 | 4 | 4 | 2 | 2 | |
|
|
|
|
|
|
|
|
|
|
14 | 12 | 8 | 6 | 6 | 4 | 4 | 2 | 2 | |
|
|
|
|
|
|
|
|
|
|
FUNCTIONAL DESCRIPTION
FOREWORD
The
ASSEMBLY
TO INSTALL BAILING HANDLE
A bailing handle (A), Fig. 1, is furnished with the polisher. The bailing handle may be installed on either side of the front housing to facilitate either right- handed or
USED AT ALL TIMES to maintain complete control of the machine.
Attach bailing handle (A) Fig. 2 with two M8 x 1 cap screws provided one of which is shown at (B) Fig. 2. Tighten securely with 6mm allen wrench provided.
5