Powermatic PM2000 manual Blade Installation/Replacement, Motor Cover

Page 12

Blade Installation/Replacement

Use care when working with or around sharp saw blade to prevent injury!

To install or replace a blade (refer to Figure 6):

1.Disconnect machine from power source.

2.Raise the blade height all the way up and set the blade tilt to 0º (refer to Handwheel Adjustments on page 14).

3.Press the arbor lock (D) in the direction shown by the arrow to engage it into the slot in the arbor (C). At the same time remove the arbor nut (loosen with a 27mm wrench if necessary).

4.Remove the collar (B).

5.Install the blade, making sure the cutting teeth at the top of the blade point toward the front of the saw. If unsure, refer to Figure 10 for the proper blade orientation.

6.Replace the collar (B) and arbor nut (A).

7.Engage the arbor lock (D) and tighten the nut

(A) with a 27mm wrench.

8.Lower the blade below the table.

Mounting Rails and Accu-Fence

With the extension wings properly aligned, the rail, guide tube and fence assembly can now be mounted to the saw. Consult the Accu-FenceOwner's Manual (Part No. M-2195079Z) for instructions.

Optional Wood Extension Table

For instructions on mounting the accessory wood extension table, or router table, consult the Accu-FenceOwner's Manual (Part No. M-2195079Z) for instructions.

Switch Installation

Referring to Figure 7:

1.Place the switch assembly (A) under the rail

(B) and guide tube (C) so that the two holes in the switch bracket (D) line up with the left two holes in the rail and guide tube.

Note: The screws and lock washers may already have been installed when the rail and guide tube were installed and need to be removed for this operation.

2.Secure with two 1/4 lock washers (E) and 1/4 x 3/4 hex cap screws (F).

Figure 6

Figure 7

Figure 8

Motor Cover

Line up the door hinges (A. Fig. 8) with the cabinet hinges (B, Fig. 8) and insert hinge pins (C, Fig. 8).

Note: The locking mechanism may require adjustment to insure proper alignment.

12

Image 12
Contents Inch Cabinet Saw Warranty and Service Warranty PeriodTable of Contents Page Page Introduction Specifications Shipping Contents Contents of the Shipping Container Extension Tables Assembly Mounting Extension WingsLock Knobs and Swivel Handles Dust ChuteBlade Installation/Replacement Motor CoverRiving Knife and Guard Installation DescriptionAdjustments Handwheel AdjustmentsGrounding Instructions Extension CordsZero-Clearance Insert Setup Castor system adjustmentTilt Stop Adjustment Miter Slot AlignmentPrecision Miter Gauge Drive BeltRiving Knife Adjustment Lateral alignmentInsert Adjustment Arbor and Arbor Bearing RemovalSafety Key Operating ControlsStart/Stop Operations OverviewKickback Rip Sawing Crosscutting Bevel and Miter Operations Do not use the standard table insert for dadoing operationsSafety Devices Feather Board and Push BlocksPush Stick Filler PieceMaintenance LubricationMiscellaneous Troubleshooting TroubleOptional Accessories Ordering Replacement PartsModel PM2000 Table Saw Parts List Side Cover AssemblyTable & Cabinet Assembly Retractable caster system, patent US 8,006,596 B2 Trunnion & Motor Assembly Parts List PM2000-MFCB PM2000-288 Trunnion & Motor Assembly Blade Guard & Miter Gauge Assembly Parts List PM2000-AKPABlade Guard & Miter Gauge Assembly Magnetic Switch Wiring DiagramsMotor Electrical Board Motor Page Page New Sanford Road LaVergne, Tennessee Phone
Related manuals
Manual 16 pages 7.52 Kb Manual 9 pages 33.54 Kb