Multiquip HS81A manual 10 9 8 7 6

Page 14

HS81A CUT-OFF SAW — CONTROLS & COMPONENTS

1

2

3

4

12

11

10 9 8 7 6 5

Figure 2. HS81A Cut-off Saw Components 1

Figures 2 and 3 shows the location of the basic controls or components for the Multiquip Model HS81A Cut-off Saw. Listed below is a brief explanation of each control or component.

1.Air Filter – Prevents dirt and debris from entering the engine air intake. Check filter periodically and keep cleaned or replace when necessary. NEVER run engine with a dirty air filter.

2. Muffler – Used to reduce noise and emissions. NEVER! touch muffler when engine is running. Allow engine to cool down.This component gets extremely hot!

3.Guard Adjustmet Knob – Allows for the adjustment of the blade guard. Turn this knob clockwise to tighten, counter-clockwise to loosen.

4.Pulley Lock Pin Hole – Insert a phillips head screw driver or similar tool into this hole to prevent the pulley from rotating.

5.V-beltTensioning Cam – Allows for the adjustment of the V-belt. To tighten V-belt turn clockwise, to slacken turn counterclockwise.

6.V-belt Cover (Pulley) – Unscrew these 3 nuts to remove the pulley V-belt cover. NEVER operate the saw with this cover removed.

7.RollerWheel – Allows for easy free movement of the saw when cutting on a flat surface.

8.V-belt Cover (Clutch) – Unscrew these 2 nuts to remove the clutch V-belt cover. NEVER operate the saw with this cover removed. It may be necessary to remove the pulley cover first before this cover can be removed.

9.Decompression Valve – Push inward when starting engine.

10. Choke Lever – Used in the starting of a cold engine, or in cold weather conditions. The choke enriches the fuel mixture.

11. Rear Handle – When starting engine, place right foot onto rear handle base. For normal operation always place one hand on the rear handle and the other hand on the upper handle. Always use two hands when operating the saw.

12.Engine ON/OFF Switch – ON position permits engine starting, OFF position stops engine operation.

PAGE 14 — HS81A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #2 (07/26/10)

Image 14
Contents SideWinder Page Page HS81A CUT-OFF SAW -TABLE of Contents Order via Fax Dealers Only Parts Ordering ProceduresBest Deal! Order via Internet Dealers Only HS81A CUT-OFF SAW Safety Message Alert Symbols HS81A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazardHS81A CUT-OFF SAW Rules for Safe Operation General Safety HS81A CUT-OFF SAW Rules for Safe OperationDiamond Blade Safety Saw Transportation SafetyHS81A CUT-OFF SAW Rules for Safe Operation EmergenciesHS81A CUT-OFF SAW Specifications Machine Operation And Safety Decals Safety Decals10 9 8 7 6 HS81A CUT-OFF SAW Controls & Components HS81A CUT-OFF SAW Blade Installation Instructions Tool Kit Blade Installation ProcedureHex KeyTool Included withTool Kit HS81A CUT-OFF SAW -WATER KIT Installation InstructionsSocket Head Cap Screw w/ Washer  Front HandleHS81A CUT-OFF SAW Blades Diamond BladeStarting HS81A CUT-OFF SAW Initial START-UP/OPERATIONFuel Check HS81A CUT-OFF SAW Initial START-UP/OPERATION Shut-downBelt Changing Procedure Belt Guard Cover RemovalHS81A CUT-OFF SAW Maintenance Reversing the Cutting Arm Procedure Tool KitReconnect the guard adjustment knob  HS81A CUT-OFF SAW Maintenance AIR/FUEL Filter Air/Fuel Filter Maintenance ProceduresHS81A CUT-OFF SAW Troubleshooting Blade HS81A CUT-OFF SAW Troubleshooting Engine Troubleshooting EngineTroubleshooting Engine DRY Filter Kits HS81A CUT-OFF SAW Filter KitsHS81A CUT-OFF SAW Explanation of Parts Section Remarks QTY. ColumnHS81A CUT-OFF SAW Suggested Spare Parts To 3 UnitsHS81A CUT-OFF SAW Muffler Assy Part Name HS81A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS81A CUT-OFF SAW Crankcase Assy Plate HS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS81A CUT-OFF SAW Fueltank Assy Part Name QTY Remarks HS81A CUT-OFF SAW Lifting Handle and Roller Assy Handle HS81A CUT-OFF SAW -THROTTLE Linkage Assy Spring HS81A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat HS81A CUT-OFF SAW Flywheel Assy Pawl SET HS81A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug HS81A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP HS81A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS81A CUT-OFF SAW Carburetor Assy Throttle Valve HS81A CUT-OFF SAW Crankshaft / Piston Assy HS81A CUT-OFF SAW Crankshaft and Piston Assy RING, Piston PINHS81A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF HS81A CUT-OFF SAW Cart Assy HS81A CUT-OFF SAW Cart Assy HS81A CUT-OFF SAW Tools HS81A CUT-OFF SAW Tools 14 x .125 x 1 20mm Arbor Terms and Conditions of Sale Parts Freight PolicyHERE’S HOW to GET Help