Multiquip HS81A manual Reversing the Cutting Arm Procedure, Tool Kit

Page 23

HS81A CUT-OFF SAW — MAINTENANCE

Reversing the Cutting Arm Procedure

NOTE

This assembly procedure permits the operator to reorient the cutting blade closer to a wall, column

 

and/or object.

 

 

 

The Multiquip Side Winder Cut-Off Saw comes with a Tool Kit

 

 

 

(Figure 20) that assist you with day to day operations.You will

 

 

 

need these tools for the maintenance of your saw.

 

 

 

Item is a versatile screwdriver/wrench that accommodates

 

 

 

common bolt/screw and nut head sizes of your saw.

 

 

 

Item is the wrench necessary to accommodate various allen

 

 

 

 

 

 

screws.

 

Figure 20. Tool Kit

 

 

 

This position displays the cutting blade on the inside (center)

 

 

 

cutting position.To reverse the blade position continue with the

 

 

 

following steps:

 

 

 

Remove the following items from the Cutting Arm Assembly

 

 

 

to expose the V-belt:

 

 

 

 

 

 

Guard Adjustment Knob

 

 

 

Two Cap Screws

 

 

 

Cover Guard

Figure 21. Inside Center Cutting Position

Loosen the belt tensioning cam and remove the three

nuts .This will take tension off the V-belt, and permit you to reverse the cutting arm.

Figure 22 BeltTensioning Cam

HS81A CUT-OFF SAW — OPERATION & PARTS MANUAL — REV. #2 (07/26/10) — PAGE 23

Image 23
Contents SideWinder Page Page HS81A CUT-OFF SAW -TABLE of Contents Order via Fax Dealers Only Parts Ordering ProceduresBest Deal! Order via Internet Dealers Only HS81A CUT-OFF SAW Safety Message Alert Symbols Over Speed Conditions Sight and Hearing hazard HS81A CUT-OFF SAW Safety Message Alert SymbolsHS81A CUT-OFF SAW Rules for Safe Operation HS81A CUT-OFF SAW Rules for Safe Operation General SafetySaw Transportation Safety Diamond Blade SafetyEmergencies HS81A CUT-OFF SAW Rules for Safe OperationHS81A CUT-OFF SAW Specifications Safety Decals Machine Operation And Safety Decals10 9 8 7 6 HS81A CUT-OFF SAW Controls & Components Tool Kit Blade Installation Procedure HS81A CUT-OFF SAW Blade Installation InstructionsFront Handle HS81A CUT-OFF SAW -WATER KIT Installation InstructionsSocket Head Cap Screw w/ Washer  Hex KeyTool Included withTool KitDiamond Blade HS81A CUT-OFF SAW BladesStarting HS81A CUT-OFF SAW Initial START-UP/OPERATIONFuel Check Shut-down HS81A CUT-OFF SAW Initial START-UP/OPERATIONBelt Guard Cover Removal Belt Changing ProcedureHS81A CUT-OFF SAW Maintenance Tool Kit Reversing the Cutting Arm ProcedureReconnect the guard adjustment knob  Air/Fuel Filter Maintenance Procedures HS81A CUT-OFF SAW Maintenance AIR/FUEL FilterHS81A CUT-OFF SAW Troubleshooting Blade Troubleshooting Engine HS81A CUT-OFF SAW Troubleshooting EngineTroubleshooting Engine HS81A CUT-OFF SAW Filter Kits DRY Filter KitsQTY. Column HS81A CUT-OFF SAW Explanation of Parts Section RemarksTo 3 Units HS81A CUT-OFF SAW Suggested Spare PartsHS81A CUT-OFF SAW Muffler Assy Part Name HS81A CUT-OFF SAW Recoil Start Assy HANDLE, Starter Rope HS81A CUT-OFF SAW Crankcase Assy Plate HS81A CUT-OFF SAW V-BELT Cover Clutch Side Assy Belt COVER, Clutch Side HS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS81A CUT-OFF SAW V-BELT Cover Pulley /BLADE Guard Assy HS81A CUT-OFF SAW Fueltank Assy Part Name QTY Remarks HS81A CUT-OFF SAW Lifting Handle and Roller Assy Handle HS81A CUT-OFF SAW -THROTTLE Linkage Assy Spring HS81A CUT-OFF SAW Flywheel Cover Assy WASHER, Flat HS81A CUT-OFF SAW Flywheel Assy Pawl SET HS81A CUT-OFF SAW Ignition Coil Assy Spring Spark Plug HS81A CUT-OFF SAW AIR Filter Assy FLANGE, PRE- FILTER, CAP HS81A CUT-OFF SAW Carburetor Mounting Assy Carburetor Mounting Assy HS81A CUT-OFF SAW Carburetor Assy Throttle Valve HS81A CUT-OFF SAW Crankshaft / Piston Assy RING, Piston PIN HS81A CUT-OFF SAW Crankshaft and Piston AssyHS81A CUT-OFF SAW Water KIT Assy VALVE, SHUT-OFF HS81A CUT-OFF SAW Cart Assy HS81A CUT-OFF SAW Cart Assy HS81A CUT-OFF SAW Tools HS81A CUT-OFF SAW Tools 14 x .125 x 1 20mm Arbor Freight Policy Terms and Conditions of Sale PartsHERE’S HOW to GET Help