Multiquip FS 1 Concrete SAW Inspection -GUARDS, Covers ANDV-BELTS, Guards and Covers Check

Page 23

FS 1 CONCRETE SAW — INSPECTION -GUARDS, COVERS ANDV-BELTS

Guards and Covers Check

V-belts and Cover

 

CAUTION:

WARNING

NEVER operate the saw without blade guards and covers (Figures 12,13 and 14) in place. DO NOT operate with the front of the blade guard raised. The blade exposure cannot exceed 180 degrees during operations. Adhere to the safety guidelines of the American National Standards Institute (ANSI) B7.1

and B7.5.

Figure 12. Mist Blade Guard

CHECK the following on the "blade guard":

■Check to ensure the capacity of the blade guard matches the diameter of your diamond blade.

■Check that the guard is bolted firmly upon the saw frame.

■Check that the spring tensioned front cover of the guard is firmly seated with the rear section of the guard, and there are no gaps.

■Check the fit of the water hoses about the water manifold. NEVER lift the blade guard while cutting.

■Check that the flood water tubes and water jets are clear and open. Test the water supply for pressure and flow (to both sides of the blade) before sawing operations.

CHECK the following on the "blade flange cover":

■Check that the flange cover seats firmly upon the bayonet fitting of the saw frame prior to operation.

■This flange cover is to be in place when cutting from either the right or left side of the saw.

NEVER attempt to check the V-belt with the engine running because severe injury can occur. Keep fingers, hands, hair and clothing away from all moving parts.

V-belts Alignment and Tensioning

This concrete saw is equipped with two premium V-belts (14") and three premimum V-belts (18") that have been aligned and tensioned by factory personnel. All two V-belts MUST be installed for proper operation of the saw. Failure to run the saw with less than two belts may damage the saw or equipment.

Use the following procedure to check the alignment of V-belts:

1.Remove the bolts that secure theV-belt cover (Figure 14) to the saw frame.

Figure 14. V-Belt Cover

2.Check uniform parallelism (Figure 15) of V-belts and pulley

(sheaves). Use a straight edge or machinists's square against both pulleys and adjust both pulleys until equally aligned.

Figure 13. Blade Flange Cover

Figure 15. Pulley Alignment

 

MQ-WHITEMAN FS1 CONCRETE SAW — PARTS & OPERATION MANUAL — REV. #3 (04/24/03) — PAGE 23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Concrete SAW Page Heres HOW to GET Help Table of Contents Parts Ordering Procedures Seriously injured if you do not follow directions FS 1 Concrete SAW Safety Message Alert SymbolsAlways wear approved eye and hearing protection FS 1 Concrete SAW Safety Message Alert SymbolsAlways wear approved respiratory protection FS 1 Concrete SAW Decals Machine Safety DecalsFS 1 Concrete SAW Rules for Safe Operation General SafetyNever transport the saw with the blade mounted Stop the engine when leaving the saw unattendedFS 1 Concrete SAW Rules for Safe Operation Never tow the saw behind a vehicleEmergencies Maintenance SafetyFS 1 Concrete SAW Rules for Safe Operation FS 1 Concrete Saw Dimensions FS 1 Concrete SAW DimensionsCrated Weight kgs lbs Weight kgsFS 1 Concrete Saw Basic Components FS 1 Concrete SAW Basic ComponentsDescription FS 1 Concrete SAW Basic Engine Components Manual FS 1 Concrete SAW General InformationFS 1 Concrete SAW General Information Water Connection/Manual/Raise Lower AssemblyEngine Oil Check Read safety instructions at the beginning of manualFS 1 Concrete SAW Inspection -ENGINE Before StartingBlade and the saw Rotation downcuts with the turn of the shaftOperating area Poor performance and/or blade damageTight closure on the surface of the blade FS 1 Concrete SAW Inspection -BLADE Placement61-68 N/m when finalizing the assembly PositionDiamond Blade Placement Procedure FS 1 Concrete SAW Inspection -BLADE PlacementCheck the following on the blade flange cover FS 1 Concrete SAW Inspection -GUARDS, Covers ANDV-BELTSGuards and Covers Check B7.5Belt Tension FS 1 Concrete SAW- Initial START-UP Place the Engine ON/OFF switch in the on positionBlade is spinning whenever the engine is running Stopping the EngineManeuvering The Saw Advance engine throttle to full Fast position FS 1 Concrete SAW OperationSaw Alignment Wet Saw OperationBlade Speed Dry Saw OperationFinishing a Cut Diamond Blades and Blade SpeedGeneral Engine Care FS 1 Concrete SAW MaintenanceGeneral Cleanliness Bearing Lubrication CareRight-Side Shaft Bearing Blade Shaft Bearing ReplacementFS1 14 Model Shown Belt ReplacementRe-install the V-belt guard Belt Tension CheckEngine Troubleshooting FS 1 Concrete SAW Troubleshooting EngineEngine Troubleshooting FS 1 Concrete SAW Troubleshooting EngineBlade Troubleshooting FS 1 Concrete SAW Troubleshooting BladeFS 1 Concrete SAW Note Items Found In the Items Number Column Items Found In the Remarks ColumnTo 3 Units FS 1 Concrete SAW Suggested Spare PartsFS 1 Concrete SAW Under Carriage Assy 10024 NUT, Nyloc 1/2-13 511471 10024 NUT, Nyloc 1/4-20 5030780730 SCREW, HHC 1/4-20 X 0948 503602FS 1 Concrete SAW Blade Shaft Assy FS 1 Concrete SAW Blade Shaft Assy FS 1 Concrete SAW Frame Assy 503015 511432511436 511502FS 1 Concrete SAW Cover Assy 503014 503012592623 0655 SCREW, HHC 5/16 18 X 3/4 492597FS 1 Concrete SAW Blade Guard Assy 503079 26250 SCREW, HHC 1/4 20 X 13/4 503103503082 503083FS 1 Concrete SAW Water System Assy 503108 HOSE, 1/2 503124491237 FS 1 Concrete SAW Manual Raise and Lower Assy 503094 4910196 KNOB, 3/8 NC 503013503093 FS 1 Concrete SAW Engine Assy 512891 H.P. Kolher Model PA-95150212.0 H.P. Kohler Model PA-941502 492054Terms and Conditions of Sale Parts Page Warranty Department Main

FS 1 specifications

The Multiquip FS 1 is a versatile piece of equipment designed for efficient fuel management and transfer. Catering primarily to construction sites, agriculture, and industrial applications, the FS 1 is known for its compact design, robust performance, and reliable functionality.

One of the main features of the Multiquip FS 1 is its high-capacity fuel tank, which is engineered to hold a substantial volume of diesel or gasoline, allowing users to refuel equipment without frequent interruptions. This fuel tank is equipped with a durable, weather-resistant cover that ensures protection against various environmental factors, extending the life of the equipment.

In terms of technology, the FS 1 incorporates advanced pumping systems that facilitate rapid fuel transfer. The pump is designed for low noise operation, reducing disturbances on job sites while ensuring efficient fuel flow. Furthermore, the inclusion of an automatic shutoff feature ensures safety during fueling operations by preventing overflows and spills, thus minimizing environmental risks.

The FS 1 is characterized by its mobility. Equipped with sturdy wheels and a reliable tow hitch, it can be easily transported from one location to another, simplifying the logistics of fuel distribution on-site. This portability is particularly beneficial in large construction projects where multiple machines require fueling at varied intervals.

Ergonomically designed, the FS 1 features user-friendly controls that simplify operation. Operators can easily manage fuel transfers, check gauge readings, and monitor flow rates without extensive training. Additionally, the FS 1 is designed to be compatible with various fuel nozzles, making it a versatile choice for different fueling needs.

The construction of the FS 1 emphasizes durability and longevity. Built with high-quality materials, it is resistant to corrosion and wear, making it suitable for demanding environments. The design also prioritizes ease of maintenance, with accessible components that allow for quick inspections and repairs.

In summary, the Multiquip FS 1 stands out for its combination of efficiency, safety, and mobility. It is an essential tool for professionals who require a reliable fuel management solution that is easy to operate and maintain. With its innovative design and advanced features, the FS 1 simplifies the fueling process, allowing users to focus on their core tasks and enhancing overall productivity on the job site.
Top Page Image Contents